Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 6341-6360 of 7723
-
Pulse-Tube Refrigeration
(The American Society of Mechanical Engineers (ASME), 1964)A very simple effect makes it possible to construct very low temperature refrigerators without the use of low temperature moving parts or the Joule-Thomson effect. The effect, which occurs in ... -
Nonlinear Aspects of the Performance of Centrifugal Pendulum Vibration Absorbers
(The American Society of Mechanical Engineers (ASME), 1964)Centrifugal pendulums have been used for many years to limit the torsional vibration of reciprocating engines. Recently small pendulums, designed to swing through amplitudes of about 45 deg, ... -
On the Buckling of Columns
(The American Society of Mechanical Engineers (ASME), 1964)An appropriate nonlinear formulation of elasticity is reduced through the usual assumptions of bending theory. It is shown that buckling problems for uniform straight columns may be studied, to ... -
Performance of Gears Under High Loads and Low Velocities
(The American Society of Mechanical Engineers (ASME), 1964)To obtain information concerning the ability of conventional parallel-shaft gears to transmit motion smoothly at low velocities under high load, experiments were conducted on a single commercial ... -
On the Vibration of a Thick Ring in Its Own Plane
(The American Society of Mechanical Engineers (ASME), 1964)A method based on beam theory is developed to describe the bending vibrations of nonthin, complete circular rings of rectangular cross section. Bending, shear, and extensional strain energies ... -
Results of a Fifteen-Year Program of Flexural Fatigue Testing of Gear Teeth
(The American Society of Mechanical Engineers (ASME), 1964)This is a report of a continuing program of testing gear teeth which had its inception in 1946. In the course of the program about 3000 gear teeth have been broken under controlled laboratory ... -
Discussion: “Comparison of Static and Dynamic Hardness of Grinding Wheels” (Peklenik, J., Lane, R., and Shaw, M. C., 1964, ASME J. Eng. Ind., 86, pp. 294–297)
(The American Society of Mechanical Engineers (ASME), 1964) -
Discussion: “Controlled-Force Grinding—A New Technique for Precision Internal Grinding” (Hahn, Robert S., 1964, ASME J. Eng. Ind., 86, pp. 287–293)
(The American Society of Mechanical Engineers (ASME), 1964) -
Discussion: “A Least-Squares Method for Computing Balance Corrections” (Goodman, Thomas P., 1964, ASME J. Eng. Ind., 86, pp. 273–277)
(The American Society of Mechanical Engineers (ASME), 1964) -
Discussion: “Performance of Gears Under High Loads and Low Velocities” (Cress, H. A., Fitzgerald, E., and Mark, D. G., 1964, ASME J. Eng. Ind., 86, pp. 245–250)
(The American Society of Mechanical Engineers (ASME), 1964) -
Discussion: “Results of a Fifteen-Year Program of Flexural Fatigue Testing of Gear Teeth” (Seabrook, John B., and Dudley, Darle W., 1964, ASME J. Eng. Ind., 86, pp. 221–237)
(The American Society of Mechanical Engineers (ASME), 1964) -
A First-Order Five-Variable Cutting-Tool Temperature Equation and Chip Equivalent
(The American Society of Mechanical Engineers (ASME), 1964)A simple first-order five-variable cutting-tool temperature predicting equation is developed by a 25−1 fractional factorial design. Only 16 testing conditions are used in the experiment. Confirmatory ... -
Chip Formation With Varying Undeformed Chip Thickness at Very Slow Speed
(The American Society of Mechanical Engineers (ASME), 1964)Steel S.A.E. 1112 cold rolled specimen was cut orthogonally at slow speed of 0.625 ipm, and the shear plane formation was examined from a series of photographs taken during a cut for cutting ... -
Markov Chain Models of Grinding Profiles
(The American Society of Mechanical Engineers (ASME), 1964)Profiles of abrasive surfaces are analyzed by means of Markov chain theory. The Chapman-Kolmogorov equations, together with recurrent-event theory, are used to deduce theoretical distributions for ... -
An Investigation of Grinding Wheel Cutting Edges
(The American Society of Mechanical Engineers (ASME), 1964)A new apparatus for microscopic observation and tracing of cutting edges of a wheel has been developed. The use of this apparatus allows us to visually witness the behavior of abrasive grains ... -
Some Transient Measurements in a Rarefaction Wave Tube
(The American Society of Mechanical Engineers (ASME), 1964)This paper reports upon an experimental investigation in which a heat-transfer instrument was designed, built, and applied in a rarefaction wave tube. An analysis of the heat-transfer instrument ... -
Characteristics of the Steam-Jet Vacuum Pump
(The American Society of Mechanical Engineers (ASME), 1964)This paper is a discussion and presentation of the theoretical and practical limitations, attainable efficiencies, general performance characteristics, and present-day regions of operation of single ... -
On the Tribomechanics of Rolling
(The American Society of Mechanical Engineers (ASME), 1964)Conventional kinematic concepts of rolling can be seriously in error if applied to heavily loaded contacts, particularly if traction is large. Two relevant theorems of rolling are stated, which ... -
Vibration of Cams Having Two Degrees of Freedom
(The American Society of Mechanical Engineers (ASME), 1964)The vibration analysis of cam-follower systems is extended to models having two degrees of freedom. Two models are considered, one in which the cam support is rigid and the follower has two ... -
Deflection of Spur Gear Teeth Cut in Thin Rims
(The American Society of Mechanical Engineers (ASME), 1964)In this paper, the complex problem of deflection of loaded spur teeth cut in thin rims is studied. Tooth-deflection curves, modified for the effect of elasticity of the gear, and rim stiffness ...