Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5921-5940 of 7723
-
Discussion: “Acceleration Axes in Spherical Kinematics” (Bottema, O., 1965, ASME J. Eng. Ind., 87, pp. 150–153)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Analysis of the Motion of Deep-Water Drill Strings—Part 2: Forced Rolling Motion” (Frost, III, M. A., and Wilhoit, Jr., J. C., 1965, ASME J. Eng. Ind., 87, pp. 145–149)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Strength of Threaded Joints for Steel Pipe” (Clinedinst, W. O., 1965, ASME J. Eng. Ind., 87, pp. 125–134)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Continuity of Cylindrical Shells Subjected to the Uniformly Distributed Longitudinal Surface Loads” (Shang, Jeng C., 1965, ASME J. Eng. Ind., 87, pp. 115–123)
(The American Society of Mechanical Engineers (ASME), 1965) -
Discussion: “Hydrodynamic Forming” (Cogan, R. M., 1965, ASME J. Eng. Ind., 87, pp. 105–109)
(The American Society of Mechanical Engineers (ASME), 1965) -
Torsion of Inhomogeneous Elastic Prismatic Bars
(The American Society of Mechanical Engineers (ASME), 1965)Torsion of elastic bars with prismatic inhomogeneities may be solved with a minor modification of Prandtl’s stress function and membrane analogy. This method may be used for the numerical ... -
A Survey of Methods of Stability Analysis of Ring-Stiffened Cylinders Under Hydrostatic Pressure
(The American Society of Mechanical Engineers (ASME), 1965)This paper presents a survey of methods of analysis of the most common types of buckling in ring-reinforced cylinders under hydrostatic pressure. Shell buckling and general instability are ... -
The Vibration of an Internally Damped Sandwich Plate Radiating Into a Fluid Medium
(The American Society of Mechanical Engineers (ASME), 1965)An analysis is given for the vibration of a long sandwich plate with linear internal damping properties. The plate is subjected to a time-harmonic pressure loading of constant amplitude and ... -
Combined Bending and Compression of a Pressurized Circular Cylindrical Membrane Column
(The American Society of Mechanical Engineers (ASME), 1965)Load-lateral deflection curves are developed for a pressurized tube of circular cross section under combined bending and compression. The tube walls are assumed to have negligible compressive ... -
Significant Factors in Vertical Spindle Abrasive Machining Tests
(The American Society of Mechanical Engineers (ASME), 1965)This paper develops and illustrates a general procedure for accurately determining the relative effect on performance of changes in wheel variables at various feed rates in vertical-spindle ... -
Rheological Aspect of Tool Wear in Machining Graphite
(The American Society of Mechanical Engineers (ASME), 1965)When machining materials such as graphite and plastics, a very interesting phenomenon can be observed in the manner of the tool wear. The faster the speed, the lower the rate of tool wear. ... -
An Analysis of the Abrasive Machining of Plane Surfaces
(The American Society of Mechanical Engineers (ASME), 1965)The grinding ratio (ratio of volume of work removed to volume of wheel consumed) is found to be related to feed rate by an equation which resembles the Taylor tool life equation for single ... -
Performance of Tungsten Carbide, Titanium Carbide, and Oxide Tools in Finish Turning of C-30 Gray Iron
(The American Society of Mechanical Engineers (ASME), 1965)Performance data were obtained for tungsten carbide, titanium carbide, and oxide tools in the finish turning of C-30 gray iron. Characteristics of typical wear patterns were examined in relation ... -
Generalized Plane Strain of Pressurized Orthotropic Tubes
(The American Society of Mechanical Engineers (ASME), 1965)The generalized Hooke’s law in cylindrical coordinates is presented in terms of directional moduli of elasticity and Poisson’s ratios. It is used in deriving a solution for long pressurized ... -
Accurate Calculation of Stress Distributions in Multiholed Plates
(The American Society of Mechanical Engineers (ASME), 1965)This paper discusses the application of the point-matching technique in obtaining the solution of many problems involving multiholed thin plates undergoing generalized plane stress. The stress ... -
Analytical Synthesis of Function Generators Using the Slider-Crank Inversion
(The American Society of Mechanical Engineers (ASME), 1965)Equations are presented which permit the synthesis of the inversion of the slider-crank mechanism for cases where three or four conditions are placed on the input and output crank rotations ... -
Buckling of Circular Plate on Elastic Foundation
(The American Society of Mechanical Engineers (ASME), 1965)The buckling loads are found for the simply supported and clamped-edge conditions for a circular plate on a springy foundation under the action of edge loading in the middle surface of the ... -
Stick-Slip Vibration of Drill Strings
(The American Society of Mechanical Engineers (ASME), 1991)The stick-slip vibration is introduced as a new mechanism to explain the large amplitude torsional oscillation of the drill strings in oil and gas well drillings. A record of field data is ... -
Localization of 3-D Objects Having Complex Sculptured Surfaces Using Tactile Sensing and Surface Description
(The American Society of Mechanical Engineers (ASME), 1991)This paper presents a method for locating 3-D objects having complex and sculptured surfaces. Among many complex shaped objects, dies, molds, gears, turbine blades, forged parts, and aerospace ... -
A Transfer Function Description of Sheet Metal Forming for Process Control
(The American Society of Mechanical Engineers (ASME), 1991)Three-dimensional forming of sheet metal parts is typically accomplished using one or two shaped tools (dies) that impart the necessary complex curvature and induce sufficient in-plane strain for ...