Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 4941-4960 of 7723
-
Surface Integrity of Die Material in High Speed Hard Machining, Part 1: Micrographical Analysis
(The American Society of Mechanical Engineers (ASME), 2000)The effects of cutting conditions and tool wear on chip morphology and surface integrity during high speed machining of D2 tool steel (60–62 Hrc) are investigated experimentally and analytically ... -
Evaluation of Minimum Zone Straightness by a Nonlinear Optimization Method
(The American Society of Mechanical Engineers (ASME), 2000)In this paper, a new algorithm, based on a nonlinear optimization method (NOM), has been developed. The accuracy as well as the reliability/robustness of the new algorithm have been verified ... -
Thermal Aspects of Grinding: The Case of Upgrinding
(The American Society of Mechanical Engineers (ASME), 2000)Conventional grinding is usually carried out in upgrinding mode, with the wheel moving in the opposite direction from the workpiece. In this paper, a thermal model is developed for upgrinding. ... -
Surface Integrity of Die Material in High Speed Hard Machining, Part 2: Microhardness Variations and Residual Stresses
(The American Society of Mechanical Engineers (ASME), 2000)The main objective of this paper is to investigate the quality and integrity of the surface produced during high speed hard machining (HSHM) of D2 tool steel in its hardened state (60–62 ... -
Finite Element Modeling of Burr Formation Process in Drilling 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 2000)A 3D finite element model was developed for the simulation of drilling burr formation processes of 304L stainless steel. The nonlinear thermo-elastic-plastic model simultaneously accounts for ... -
Comparisons Between the Shearing Properties of Alpha-Brass as Derived From the Cutting Process and From Static and Impact Torsion Tests
(The American Society of Mechanical Engineers (ASME), 1960) -
Correlation of Bendability of Materials With Their Tensile Properties
(The American Society of Mechanical Engineers (ASME), 1960)With the advent of high-temperature-resistant materials in the sheet-metal industry, it is becoming increasingly important to treat the subject of minimum or “critical” bend radius analytically. ... -
A Photoelastic Analysis of Machining Stresses
(The American Society of Mechanical Engineers (ASME), 1960)Direct measurements of the distributions of normal and frictional stresses on a rake face under cutting conditions have been considered to be practically impossible. However, as reported in this ... -
Tensile and Short-Time Creep Properties of N-155 Alloy Sheet
(The American Society of Mechanical Engineers (ASME), 1960)The special test equipment and procedures developed for the evaluation of ultrashort-time elevated-temperature mechanical properties of materials are described herein. The tensile and high-stress ... -
Erratum: “Synthesis of Epicyclic Gear Trains Using the Velocity Ratio Spectrum” (Journal of Engineering for Industry, 1960, 82, pp. 173–178)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Deformation and Moments in Elastically Restrained Circular Plates Under Arbitrary Load or Linear Thermal Gradient” (Zaid, M., and Forray, M., 1960, ASME J. Eng. Ind., 82, pp. 423–438)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Inertial Effects in a Multiple-Ball Transmission” (Rouverol, W. S., 1960, ASME J. Eng. Ind., 82, pp. 399–406)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Design by Quantitative Factor of Safety” (Su, Hsuan-Loh, 1960, ASME J. Eng. Ind., 82, pp. 387–391)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Mechanical Vibration Filters With Nonlinear Characteristics” (Worley, Will J., 1960, ASME J. Eng. Ind., 82, pp. 369–375)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Optimum Tolerances of Sheet Materials for Flight Vehicles” (Hoffman, George A., 1960, ASME J. Eng. Ind., 82, pp. 363–366)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “New Developments in the Theory of the Metal-Cutting Process: Part I. The Ploughing Process in Metal Cutting” (Albrecht, P., 1960, ASME J. Eng. Ind., 82, pp. 348–357)
(The American Society of Mechanical Engineers (ASME), 1960) -
Discussion: “Correlation of Bendability of Materials With Their Tensile Properties” (Datsko, J., and Yang, C. T., 1960, ASME J. Eng. Ind., 82, pp. 309–313)
(The American Society of Mechanical Engineers (ASME), 1960) -
Sensor Optimization for Fault Diagnosis in Single Fixture Systems: A Methodology
(The American Society of Mechanical Engineers (ASME), 1999)Fixture fault diagnosis is a critical component of currently evolving techniques aimed at manufacturing variation reduction. The impact of sensor location on the effectiveness of fault-type ... -
Impact Fracture of Screws for Disassembly
(The American Society of Mechanical Engineers (ASME), 1999)Environmental legislation urges manufacturers to develop effective technologies to cope with obsolete products. The goal is to optimize the disassembly procedure (cost, efficiency) with emphasis ... -
Neural Adaptive Control for Positioning Fabric on a Frictional Surface
(The American Society of Mechanical Engineers (ASME), 1999)This research focuses on real-time position control for draping fabric sliding on a high friction surface. Although fabrics are usually positioned on smooth surfaces with fixed fabric guides to ...