Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 4521-4540 of 7723
-
Basic Investigation of Built-Up-Edge
(The American Society of Mechanical Engineers (ASME), 1968)The formation of a built-up-edge has been differentiated into two mechanisms, that is, adhesion or nucleation of built-up-edge and growth of adhered metal. As to adhesion, the affinity between ... -
The Effect of Chip Adsorption on Selective Depletion From a Multi-Component Synthetic Metalworking Fluid
(The American Society of Mechanical Engineers (ASME), 2003)Certain components found in metalworking fluid formulations are known to be prone to selective depletion via adsorption onto the surfaces of particulate generated during metal cutting operations. ... -
Modeling Forces Including Elastic Recovery for Internal Thread Forming
(The American Society of Mechanical Engineers (ASME), 2003)This paper presents a model that incorporates the effects of elastic recovery for the prediction of thrust and torque experienced by a forming tap during an internal thread forming process. ... -
Experimental Cutting Tool Temperature Distributions
(The American Society of Mechanical Engineers (ASME), 2003)High temperatures in machining cutting zones activate wear mechanisms that decrease tool life and increase production costs and yet this phenomenon is not fully understood nor characterized. ... -
Dimensional Errors of Fixtures, Locating and Measurement Datum Features in the Stream of Variation Modeling in Machining
(The American Society of Mechanical Engineers (ASME), 2003)Machining processes are usually multi-station processes involving a large number of operations and several locating datum changes. Machining errors are thus introduced, transformed and accumulated ... -
A Stability Algorithm for the General Milling Process: Contribution to Machine Tool Chatter Research—7
(The American Society of Mechanical Engineers (ASME), 1968)In this paper, a method of stability analysis for the general milling process is given. The milling operation is described by a linear differential-difference equation with periodic coefficients. ... -
A Stability Algorithm for a Special Case of the Milling Process: Contribution to Machine Tool Chatter Research—6
(The American Society of Mechanical Engineers (ASME), 1968)In an effort to determine the stability of the milling process, and due to the complexity of its describing equation, a special case of this equation is considered. In this way, it is ... -
A General Formulation of the Milling Process Equation: Contribution to Machine Tool Chatter Research—5
(The American Society of Mechanical Engineers (ASME), 1968)In the cutting process, forces are induced at each of the cutter teeth in contact with the workpiece, and these forces in turn excite the machine tool structure. Due to the inherent feedback ... -
The Strength of Thick Cylinders Subjected to Repeated Internal Pressure
(The American Society of Mechanical Engineers (ASME), 1960)In April, 1956, the authors presented to The Institution of Mechanical Engineers a paper entitled “Fatigue Under Triaxial Stress: Development of a Testing Machine and Preliminary Results,” and ... -
Reducing Wear in an Electromagnetic Clutch
(The American Society of Mechanical Engineers (ASME), 1968)An analytical model of an electromagnetically operated friction-disk clutch is constructed in order to determine the wear on the clutch face. The face consists of two materials—metal rings and ... -
Stress Concentration Factors in Shouldered Shafts Subjected to Combinations of Flexure and Torsion
(The American Society of Mechanical Engineers (ASME), 1968)Geometric stress concentration factors were determined experimentally for shouldered aluminum shafts subjected to combinations of flexural and torsional loads. Diameter ratios were varied from 0.42 ... -
Application of the Positive Thermoelastic Coefficients of Nickel-Iron Alloys to Wide-Temperature-Range Belleville Springs
(The American Society of Mechanical Engineers (ASME), 1968)A method for producing a spring of constant spring-rate versus temperature up to the range of 1000 deg F is presented by series stacking of Belleville spring washers. Several different materials ... -
Bending of Circular Plates Under a Uniform Load on a Concentric Circle—Part II
(The American Society of Mechanical Engineers (ASME), 1968)The basic equations of deflection, slope, and moments for a thin, flat, circular plate subjected to a uniform load on a concentric circle were derived for four generalized cases. From these ... -
Bending of Circular Plates Under a Variable Symmetrical Load—Part I
(The American Society of Mechanical Engineers (ASME), 1968)The basic equations of deflection, slope, and moment for a thin, flat, circular plate, under a symmetrical variable load, for a constant force divided by the square of the radial distance, ... -
A Fuel Cell Power Plant for a Deep Diving Submarine
(The American Society of Mechanical Engineers (ASME), 1968) -
Underwater Power From Aluminum
(The American Society of Mechanical Engineers (ASME), 1968)A thermochemical power system having the highest theoretical performance (hp-hr/cu ft propellants) and particularly suited for underwater applications (power, heat, and propulsion) is described. In ... -
Effect of a Time-Dependent Stenosis on Flow Through a Tube
(The American Society of Mechanical Engineers (ASME), 1968)A common occurrence in the arterial system is the narrowing of arteries due to the development of atherosclerotic plaques or other types of abnormal tissue development. As these growths project ... -
Viscoelastic Properties of Soft Tissue by Discrete Model Characterization
(The American Society of Mechanical Engineers (ASME), 1968)In order to study the response of the human body to acceleration and force, it is necessary to be able to relate force to deformation in various body tissues. Problems wherein this becomes ... -
Temperature Distributions in Drilling
(The American Society of Mechanical Engineers (ASME), 1968)An analytical temperature distribution along the cutting edge and on the flank face of a drill is obtained using Tsueda’s and Loewen and Shaw’s equations after modifications. Experimental ... -
The Theory of the Ideal Design of a Compound Vessel
(The American Society of Mechanical Engineers (ASME), 1960)A general theory for the elastic design of a compound cylinder made by shrinking together many concentric cylinders is described. Each cylinder may have entirely different strength and operate ...