Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 4321-4340 of 7723
-
Vibration Frequencies in High-Speed Milling Processes or a Positive Answer to Davies, Pratt, Dutterer and Burns
(The American Society of Mechanical Engineers (ASME), 2004)The stability charts of high-speed milling are constructed. New unstable regions and vibration frequencies are identified. These are related to flip bifurcation, i.e. period doubling vibrations ... -
Generation of Defects Due to Machining of TiAl Intermetallic Compound and Their Effects on Mechanical Strength
(The American Society of Mechanical Engineers (ASME), 2004)The generation of machining defects and their effect on bending strength characteristics are discussed with respect to a TiAl intermetallic compound, which is attracting much attention as a ... -
The Influence of Fluid Management Policy and Operational Changes on Metalworking Fluid Functionality
(The American Society of Mechanical Engineers (ASME), 2004)This paper discusses the influence of metalworking fluid management policy and operational changes on metalworking fluid functionality in terms of lubricating and cooling ability. Several important ... -
Fluid Performance Study for Groove Grinding a Nickel-Based Superalloy Using Electroplated Cubic Boron Nitride (CBN) Grinding Wheels
(The American Society of Mechanical Engineers (ASME), 2004)The performance of three water-based grinding fluids was analyzed and compared to a neat oil tested under the same process conditions. Light optical and scanning electron microscopy observations ... -
Flank Wear of Edge-Radiused Cutting Tools Under Ideal Straight-Edged Orthogonal Conditions
(The American Society of Mechanical Engineers (ASME), 2004)Understanding the effects of tool wear is critical to predicting tool life, the point at which tool performance, in terms of power requirement, dimensional error, surface finish, burring, or ... -
Multi Frequency Solution of Chatter Stability for Low Immersion Milling
(The American Society of Mechanical Engineers (ASME), 2004)Finish milling is usually required in the peripheral milling of thin aircraft webs with long end mills, where the structures are flexible and radial depths of cut are small. The spindle speed ... -
Added Stability Lobes in Machining Processes That Exhibit Periodic Time Variation, Part 1: An Analytical Solution
(The American Society of Mechanical Engineers (ASME), 2004)An added family of stability lobes, which exists in addition to the traditional stability lobes, has been identified for the case of periodically time varying systems. An analytical solution ... -
Character and Behavior of Mist Generated by Application of Cutting Fluid to a Rotating Cylindrical Workpiece, Part 2: Experimental Validation
(The American Society of Mechanical Engineers (ASME), 2004)In Part 1 of this paper a model was developed to describe the formation mechanisms and dynamic behavior of cutting fluid mist. This part of the paper focuses on an experimental investigation ... -
Deposition Technologies For Micromanufacturing: A Review
(The American Society of Mechanical Engineers (ASME), 2004)This paper discusses the microdeposition technologies used in the fabrication of meso- and microscale structures. The ability to process a wide range of materials and the flexibility to build ... -
Effects of Spherical Targets on Capacitive Displacement Measurements
(The American Society of Mechanical Engineers (ASME), 2004)Capacitive displacement sensors are widely used in precision manufacturing and metrology because they measure displacements with nanometer resolution. Prior literature usually treats capacitive sensors ... -
A Simulation-based Correlation of Cross-Sectional Area of the Thin Film Produced by Laser Chemical Vapor Deposition With a Moving Laser Beam
(The American Society of Mechanical Engineers (ASME), 2004)A parametric study on shape and cross-sectional area of the thin film produced by Laser Chemical Vapor Deposition (LCVD) with a moving laser beam is presented. The problem is formulated in ... -
Nanoparticle Additive Manufacturing of Ni-H13 Steel Injection Molds
(The American Society of Mechanical Engineers (ASME), 2004)This paper reports a novel solid freeform fabrication process, Nanoparticle Additive Manufacturing (NAM), for dispersing nanoparticles into molten matrix for improved mechanical properties. In ... -
Novel Sensor Fabrication Using Direct-Write Thermal Spray and Precision Laser Micromachining
(The American Society of Mechanical Engineers (ASME), 2004)This work presents a direct-write technique for rapid prototyping and manufacturing of sensors onto structural and functional components for many diverse applications. The technique combines thermal ... -
Scanning Grating Microinterferometer for MEMS Metrology
(The American Society of Mechanical Engineers (ASME), 2004)Quality control and metrology are critical to improved productivity and yield in MEMS design and production. This paper presents a micrograting interferometer for use in measuring MEMS devices. ... -
Data Mining for Subassembly Selection
(The American Society of Mechanical Engineers (ASME), 2004)The paper presents a model and an algorithm for selection of subassemblies based on the analysis of prior orders received from the customers. The parameters of this model are generated using ... -
Three Dimensional Imaging of LIGA-Made Microcomponents
(The American Society of Mechanical Engineers (ASME), 2004)Nickel and nickel-alloy microparts sized on the order of 5–1000 microns have been imaged in three dimensions using a new microscopic technique, Digital Volumetric Imaging (DVI). The gears were ... -
A Slicing Procedure for 5-Axis LaserAided DMD Process
(The American Society of Mechanical Engineers (ASME), 2004)The 5-axis layered manufacturing technology facilitates fabrication of a part with overhanging features without the use of supports, thereby making a direct-to-use part from the layered manufacturing ... -
Character and Behavior of Mist Generated by Application of Cutting Fluid to a Rotating Cylindrical Workpiece, Part 1: Model Development
(The American Society of Mechanical Engineers (ASME), 2004)Increasing attention is being devoted to the airborne emissions resulting from a variety of manufacturing processes because of health, safety, and environmental concerns. In this two-part paper, ... -
Mechanical Approach to Nanomachining of Silicon Using Oxide Characteristics Based on Tribo Nanolithography (TNL) in KOH Solution
(The American Society of Mechanical Engineers (ASME), 2004)The TNL (Tribo Nanolithography) method in aqueous solution uses the atomic force microscopy as a machining tool for the nanoscale fabrication of silicon. A specially designed cantilever with a ... -
Development of an Assembly-free Process Based on Virtual Environment for Fabricating 3D Microfluidic Systems Using Microstereolithography Technology
(The American Society of Mechanical Engineers (ASME), 2004)As it is difficult to construct a microfluidic system composed of micromixers, microchannels, and/or microchambers in a single process, an assembly process is typically used. Using microstereolithography ...