Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 2061-2080 of 7723
-
Decelerative Cutting of 6061-T9 Aluminum, 65-35 Brass, and TPE Copper With Constant Impact Energy
(The American Society of Mechanical Engineers (ASME), 1973)The chip formation process during metal cutting in which the cutting velocity is permitted to decrease freely is examined from an experimental standpoint. Metal cutting data are obtained from ... -
New Solutions to Rigid-Plastic Deformation Problems Using a Matrix Method
(The American Society of Mechanical Engineers (ASME), 1973)The matrix method for the analysis of rigid-plastic deformation problems was described and applied to simple compression of cylinders and plane-stress bore expanding and flange drawing. In cylinder ... -
The Prediction of Press Loads in Deep Drawing With Various Conditions of Lubrication at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1973)The present work is introduced and is shown to be a logical extension of work by Chung and Swift, Ray and Berry, et al. The authors introduce the deep drawing process and analyze the ... -
Differential Pressure Extrusion Through Double Reduction Dies
(The American Society of Mechanical Engineers (ASME), 1973)Differential pressure extrusion using double reduction dies was examined. Axisymmetric extrusion experiments using superplastic eutectic alloy of lead-tin were carried out for both single and double ... -
Cutting Fluids Performance: Part 1—Optimization of Pressure for “Hi-Jet” Method of Cutting Fluid Application
(The American Society of Mechanical Engineers (ASME), 1973)The results of a series of short-run cutting tests conducted with “Hi-jet” system using four common commercially available fluids are presented. The possibility of using these tests for on-the-spot ... -
On the Surface Finish-Metal Removal Relationship in Precision Grinding
(The American Society of Mechanical Engineers (ASME), 1973)A semiempirical equation representing the average chip thickness existing during grinding is presented. The scatter of surface finish data obtained using high and low wheel-speeds and wheel-work ... -
On the Mechanics of Micro-Thin Foil Production
(The American Society of Mechanical Engineers (ASME), 1973)The mechanics of micro-thin foil or leaf production by hammering has been analyzed. It was found that the metal foil cannot be reduced by a compression process alone because of the large ... -
Impact Extrusion—Upper Bound Analysis of the End of the Stroke
(The American Society of Mechanical Engineers (ASME), 1973)The upper bound approach is used to analyze the final stage of impact extrusion of a thin or thick-walled cup. The results of two different velocity fields are compared. The prediction and ... -
Tensile Strength of Composite Materials—Part 1: Upper Bound Analysis
(The American Society of Mechanical Engineers (ASME), 1973)The upper bound approach is applied to a simple model for a composite material and an expression for relative strength of a composite is developed. Relative strength of the reinforcing particle, ... -
Springback of Wire Products Considering Natural Strain
(The American Society of Mechanical Engineers (ASME), 1973)This paper makes use of the Ramberg-Osgood stress-strain relationship to evaluate the springback angle for wire products. Natural strain is present in the analysis. In order to incorporate the ... -
Characterization of Abrasive Tools by Continuous Time Series
(The American Society of Mechanical Engineers (ASME), 1973)A succinct characterization of abrasive tools using continuous time series is developed. It is based on three parameters: natural frequency ωn , damping factor ζ, and variance γ0 . These ... -
Tensile Strength of Composite Materials—Part 2: Interpretation of Analysis
(The American Society of Mechanical Engineers (ASME), 1973)The upper bound equation derived in Part 1 is manipulated to obtain more detailed information about composite strength and deformation behavior. Several behavior transitions which occur are ... -
Inhomogeneous Shearing During Continuous Chip Formation
(The American Society of Mechanical Engineers (ASME), 1973)Metallographic examination of chips cut from a directionally solidified eutectic provided direct evidence of discontinuous shearing in continuous chip formation. The built-in grid of the eutectic ... -
The Effect of Abrasion Resistance and Thermal Properties of the Cemented Carbide Cutting Tool Grade on the Flank Wear Characteristics
(The American Society of Mechanical Engineers (ASME), 1973)Correlation of the wear characteristics with abrasion resistance factor—1/(vol. loss) in a standard test—has been established in a low speed range where the temperatures involved in the cutting ... -
An Automatic V-Belt Transmission With an Asymmetrical Belt
(The American Society of Mechanical Engineers (ASME), 1973)A variable speed, V-belt transmission in which the belt has an asymmetrical cross-section was studied. The sliding sheaves adjust automatically to varying torque and speed requirements. A complete ... -
Static Analysis of a Laminated Beam
(The American Society of Mechanical Engineers (ASME), 1973)The governing differential equation and natural and rigid boundary conditions have been obtained for a three-layer beam having a middle layer which is primarily shear carrying, using a variational ... -
Stability and Kinematic Accuracy of Hydraulic Copying Mechanisms in Metal Cutting
(The American Society of Mechanical Engineers (ASME), 1973)The nature and the size of the cutting forces were investigated to develop a model that accounts for their fluctuation. Due to the interaction between the velocity of the power cylinder and ... -
Allocation of Tolerances to Minimize Cost of Assembly
(The American Society of Mechanical Engineers (ASME), 1973)When there are variations in the costs of producing the dimensions directly involved in an assembly, the paper shows how to allocate the tolerances to give the assembly of minimum cost. -
Dynamic Response of Pressurized Thin Cylindrical Shells Subjected to Torsional Loads
(The American Society of Mechanical Engineers (ASME), 1973)This paper presents a theoretical analysis of the transient and steady-state response of a thin cylindrical shell of finite length, simply supported at both ends, under a uniform initial biaxial ... -
An Analysis of Control Methods for Galloping Systems
(The American Society of Mechanical Engineers (ASME), 1973)It is shown that the motion of a galloping system can be quenched by using (a) linear, tuned, damped vibration absorbers, (b) aerodynamic in-span dampers, or (c) spring-damper support systems. ...