Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 2001-2020 of 7723
-
Measurement of Powder Properties for Hopper Design
(The American Society of Mechanical Engineers (ASME), 1973)It is common practice in powder technology to run shear tests for characterizing the flowability of powders. To measure these shear properties the flow factor tester of Jenike is mainly used. ... -
Preliminary Estimate of Mixing Effect of Nonsegregating Materials in a Plug-Flow Bin
(The American Society of Mechanical Engineers (ASME), 1973) -
Feeding Calcine Dust With a Belt Feeder at Falconbridge
(The American Society of Mechanical Engineers (ASME), 1973)This paper describes a bin for feeding dry calcine dust at a uniform rate of up to 90 TPH directly onto a belt. A small amount of air is injected into the bin to ensure controlled flow. ... -
Flow Behavior of Hematite Slurries
(The American Society of Mechanical Engineers (ASME), 1973)This paper describes our laboratory study of the flow behavior of aqueous hemalite slurries. Viscosity and flow data are given for slurries of up to 40 percent hematite by volume (76 percent ... -
Minimizing Segregation in Bunkers
(The American Society of Mechanical Engineers (ASME), 1973)Bunkers used in steelworks sinter plants and other applications need to be designed and operated so that the feed emerging is unsegregated. A series of model tests has been carried out to ... -
The Design of a Linear “Out of Phase” Vibratory Conveyor
(The American Society of Mechanical Engineers (ASME), 1973)This paper describes the development of a linear “out-of-phase” vibratory conveyor. The “out-of-phase” effect is achieved by controlling the components of motion normal to and parallel to the ... -
Aeration Apparatus Converts Bin From Funnel-Flow to Mass-Flow Characteristics
(The American Society of Mechanical Engineers (ASME), 1973)A properly designed hopper provides cost control through increased unloading reliability, improved storage space utilization, steadier discharge rates, and improved blending of discharged materials. ... -
An Evaluation of the Jenike Bunker Design Method
(The American Society of Mechanical Engineers (ASME), 1973)Flow blockage in steelworks bunkers is a major source of trouble. The correct design of bunkers to ensure flow would result in reduced capital and operating costs. The Jenike method of bunker ... -
Flow Patterns and Wall Stresses in a Mass-Flow Bunker
(The American Society of Mechanical Engineers (ASME), 1973)Observations are reported of the shear and normal stresses on the walls of a small mass flow bunker and of the variations of density in the flowing material. Changes in wall stresses which ... -
The Bougainville 975 TPH Feeder
(The American Society of Mechanical Engineers (ASME), 1973)This paper describes the traveling tripper-surge bin-feeder-screen system as well as the hopper design for mass flow of material. Highlights of the calculations are brought out, particularly those ... -
Bin Loads—Part 4: Funnel-Flow Bins
(The American Society of Mechanical Engineers (ASME), 1973)This is one of a series of papers by the authors on the loads exerted by bulk solids on the walls of containing vessels. In this paper, design formulas and charts are presented for mass-flow ... -
Application of Pseudo-Random Test Signals and Cross Correlation to the Identification of Bulk Handling Plant Dynamic Characteristics
(The American Society of Mechanical Engineers (ASME), 1973)In the determination of the dynamic characteristics of bulk handling systems the complexity of the problem usually makes experimental identification necessary. Experimental techniques which are ... -
Discussion: “Measurement of Powder Properties for Hopper Design” (Schwedes, J., 1973, ASME J. Eng. Ind., 95, pp. 55–59)
(The American Society of Mechanical Engineers (ASME), 1973) -
Bin Loads—Part 3: Mass-Flow Bins
(The American Society of Mechanical Engineers (ASME), 1973)This is one of a series of papers by the authors on the loads exerted by bulk solids on the walls of containing vessels. In this paper, design formulas and charts are presented for mass-flow ... -
Discussion: “Fracture Resistance of Wire-Wrapped Cylinders” (Shoemaker, A. K., Melville, T., and Steiner, J. E., 1973, ASME J. Eng. Ind., 95, pp. 219–226)
(The American Society of Mechanical Engineers (ASME), 1973) -
Bin Loads—Part 2: Concepts
(The American Society of Mechanical Engineers (ASME), 1973)This is one of a series of papers by the authors on the loads exerted by bulk solids on containing bins. In this paper, the concepts are described. In particular, the principle of minimum ... -
Discussion: “Karman Vortex Streets and Flow-Induced Vibrations in Tube Banks” (Chen, Y. N., 1973, ASME J. Eng. Ind., 95, pp. 410–412)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “An Evaluation of the Mechanical Properties of Mn-Mo and Mn-Mo-Ni Steels” (Swift, R. A., and Gulya, J. A., 1973, ASME J. Eng. Ind., 95, pp. 235–242)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Process Application and Design of Large Power Output Turboexpanders” (Linhardt, H. D., 1973, ASME J. Eng. Ind., 95, pp. 227–232)
(The American Society of Mechanical Engineers (ASME), 1973) -
Acceleration Resolution Applied to Analog Mechanism Simulation
(The American Society of Mechanical Engineers (ASME), 1973)The investigator using analog or hybrid computers in mechanism study encounters great complexity and a requirement for considerable equipment when a simulation is extended to accelerations and ...