Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1761-1780 of 7723
-
Discussion: “Engineering in Resuscitation” (Smilg, Benjamin, 1961, ASME J. Eng. Ind., 83, pp. 107–117)
(The American Society of Mechanical Engineers (ASME), 1961) -
Stresses in Cylindrical Tubes Subjected to a Pressure Band
(The American Society of Mechanical Engineers (ASME), 1974)In this work, the stresses in stiffened thick tubes are calculated. The results obtained from the proposed theory are compared with experimental values of stresses measured at the outer surface ... -
Discussion: “Necessary and Sufficient Existence Criteria of Overconstrained Five-Link Spatial Mechanisms With Helical, Cylinder, Revolute, and Prism Pairs” (Pamidi, P. R., Soni, A. H., and Dukkipati, R. V., 1973, ASME J. Eng. Ind., 95, pp. 737–743)
(The American Society of Mechanical Engineers (ASME), 1974) -
The Orbital Movement and the Damping of the Fluidelastic Vibration of Tube Banks Due to Vortex Formation: Part 3—Damping Capability of the Tube Bank Against Vortex-Excited Sonic Vibration in the Fluid Column
(The American Society of Mechanical Engineers (ASME), 1974)The damping criterion previously proposed by Chen 1964/1968 is evaluated with respect to a series of existing units using various fuels. The critical value of this criterion, which was given ... -
Stress Relaxation of Tension-Compression Members Having Constant Elongations
(The American Society of Mechanical Engineers (ASME), 1974)This paper presents a generalization of a commonly used stress relaxation relationship. The generalization applies to tension or compression members which have constant elongations and which obey ... -
Calculation of Forced Whirling and Stability of Centrifugal Pump Rotor Systems
(The American Society of Mechanical Engineers (ASME), 1974)Although common problems with well established solutions are met in all rotor systems embodying hydrodynamic bearings, a number of factors peculiar to centrifugal pumps radically affect their ... -
Discussion: “Transient Response of Rotor-Bearing Systems” (Kirk, R. G., and Gunter, E. J., 1974, ASME J. Eng. Ind., 96, pp. 682–690)
(The American Society of Mechanical Engineers (ASME), 1974) -
Effect of Hydrostatic Pressure on Corrosion-Fatigue at High Frequency
(The American Society of Mechanical Engineers (ASME), 1974)An experimental investigation into the effect of hydrostatic pressure on corrosion-fatigue at a frequency of 20,000 cycles per sec is reported for a number of materials currently considered for ... -
Discussion: “Analysis and Synthesis of Mechanical Error in Linkages—A Stochastic Approach” (Dhande, S. G., and Chakraborty, J., 1973, ASME J. Eng. Ind., 95, pp. 672–676)
(The American Society of Mechanical Engineers (ASME), 1974) -
The Orbital Movement and the Damping of the Fluidelastic Vibration of Tube Banks Due to Vortex Formation: Part 1—The Interplay Between the Self-Excited Vibration of the Single Circular Cylinder and the Karman Vortex
(The American Society of Mechanical Engineers (ASME), 1974)In the present paper a series of experimental results obtained by several authors on the phenomena of the vortex street behind a vibrating cylinder are analysed. From this we can establish a ... -
Semiclosed Cycle Internal Combustion Engine Utilizing Cryogenic Exhaust Solidification for Undersea Applications
(The American Society of Mechanical Engineers (ASME), 1974)The paper describes the design, hardware, testing, and performance of a breadboard semi-closed cycle power system proposed for undersea operations by the Naval Undersea Center. The work was ... -
Transient Response of Inelastically Constrained Rigid-Body Systems
(The American Society of Mechanical Engineers (ASME), 1974)An energy rate balance is employed to develop the incremental equations of motion for a shock loaded, inelastically constrained rigid-body structural system. Lagrangian multipliers provide the ... -
Vibration Analysis of a Damped Machinery Foundation Structure Using the Dynamic Stiffness Coupling Technique
(The American Society of Mechanical Engineers (ASME), 1974)A detailed dynamic analysis is made of a heavily damped foundation structure designed for the multidirectional isolation of machinery vibrations. The principal components of the structure are ... -
Fifty Years of Management—A Look Back and a Look Forward
(The American Society of Mechanical Engineers (ASME), 1961)The decade which this report discusses, the decade of the Fifties, has been a time of fulfillment in management. It has also been a decade of conclusion for historical trends. Now we are ... -
Dynamic Response of Three-Dimensional Framed Structures
(The American Society of Mechanical Engineers (ASME), 1974)The orthogonality condition for vibrating three-dimensional framed structures has been directly applied to solve initial value problems. In solving the dynamic response problems due to force and ... -
On Sparse Matrices in Finite Element Wave Propagation
(The American Society of Mechanical Engineers (ASME), 1974)The finite element method has been extensively applied to the solution of static and dynamic problems. Some work has been done in finite element wave propagation but matrix techniques typically ... -
Vibration of Frame Foundation With Bilinear Hysteresis for Rotating Machinery
(The American Society of Mechanical Engineers (ASME), 1974)The vibration of a single-story frame with bilinear hysteresis supporting a rotating machine is analyzed. The excitation force caused by the rotating unbalanced mass of the machine has a frequency ... -
Towards the Efficient Vibration Analysis of Shrouded Bladed Disk Assemblies
(The American Society of Mechanical Engineers (ASME), 1974)Prediction of the vibration properties of turbomachine blades and disks is an essential part of turbine design. However, the complexity of modern machines and the necessity to analyze the ... -
Harmonic Response of Cylindrical Shells
(The American Society of Mechanical Engineers (ASME), 1974)The normal mode method is used to determine the steady state response of a simply supported, uniform thin cylindrical shell to a radical harmonic force with hysteretic damping included in the ... -
Heat Induced Vibration of a Rectangular Plate
(The American Society of Mechanical Engineers (ASME), 1974)The purpose of this paper is to investigate thermally induced vibration of a rectangular plate with one edge fixed and other three edges simply supported. The plate was subjected to a sinusoidal ...