Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1541-1560 of 7723
-
Effect of Deep Penetration of Interleaf on Delamination Resistance in GFRP
(The American Society of Mechanical Engineers (ASME), 2016)The problem of improving the delamination resistance and toughness of laminate fiber-reinforced composites especially for the drop-off structure is receiving considerable attention with the increasing need and application ... -
Multiobjective Optimization Under Uncertainty in Advanced Abrasive Machining Processes Via a Fuzzy-Evolutionary Approach
(The American Society of Mechanical Engineers (ASME), 2016)This paper considers multiobjective optimization under uncertainty (MOOUC) for the selection of optimal cutting conditions in advanced abrasive machining (AAM) processes. Processes considered are water jet machining (WJM), ... -
Simulation of Dynamic Behavior and Prediction of Optimal Welding Current for Short-Circuiting Transfer Mode in GMAW
(The American Society of Mechanical Engineers (ASME), 2016)An improved “mass–spring” model to analyze the entire short-circuiting transfer (SCT) dynamic process based on the association between the arcing and circuiting phases has been proposed. This paper analyses the basic ... -
Automated Surface Defect Detection Using High-Density Data
(The American Society of Mechanical Engineers (ASME), 2016)State-of-the-art measurement technologies, such as 3D laser scanners, provide new opportunities for knowledge discovery and development of quality control (QC) strategies for complex manufacturing systems. These technologies ... -
Aesthetics and Gloss of Ground Surfaces: A Review on Measurement and Generation
(The American Society of Mechanical Engineers (ASME), 2016)Visual appearance of an object significantly influences a consumer's choice and largely controls the market economy. The perceived quality of products is governed by surface's optical properties (reflection, refraction, ... -
On the Parameter Identification of Polynomial Anisotropic Yield Functions
(The American Society of Mechanical Engineers (ASME), 2016)Nonquadratic anisotropic yield functions have been developed in recent years for many lightweight automotive sheet metals. Realization of the improved performance of these advanced anisotropic yield functions depends in ... -
Effect of Roll Configuration on the Leveling Effectiveness of Tail-Up Bent Plate Using Finite-Element Analysis
(The American Society of Mechanical Engineers (ASME), 2016)The finite-element method (FEM) has been used to numerically investigate the effect of work roll configuration on the leveling effectiveness of tail-up bent plates. Leveling is a process used to minimize shape defects, ... -
Study on the Generalized Holo-Factors Mathematical Model of Dimension-Error and Shape-Error for Sheet Metal in Stamping Based on the Back Propagation (BP) Neural Network
(The American Society of Mechanical Engineers (ASME), 2016)Precision improvement in sheet metal stamping has been the concern that the stamping researchers have engaged in. In order to improve the forming precision of sheet metal in stamping, this paper devoted to establish the ... -
Fatigue Life Prediction for Overlap Friction Stir Linear Welds of Magnesium Alloys
(The American Society of Mechanical Engineers (ASME), 2016)This work was undertaken to analyze the stress/strain state at the critical sites in friction stir welded specimens and, further, to assess the fatigue strength of friction stir welded specimens with conventional fatigue ... -
Parameter Inference Under Uncertainty in End-Milling γ′-Strengthened Difficult-to-Machine Alloy
(The American Society of Mechanical Engineers (ASME), 2016)Nickel-based alloys are those of materials that are maintaining their strength at high temperature. This feature makes these alloys a suitable candidate for power generation industry. However, high wear rate and tooling ... -
Processing Optimization in Multiheating Positions for Laser Thermal Adjustment of Actuators
(The American Society of Mechanical Engineers (ASME), 2016)Laser thermal adjustment as an application of laser forming in microsystems attracts much attention. Previous work on laser thermal adjustment of the two-bridge actuator (TBA) shows that the deformations induced by laser ... -
Curing-Induced Debonding and Its Influence on Strength of Adhesively Bonded Joints of Dissimilar Materials
(The American Society of Mechanical Engineers (ASME), 2016)Adhesive bonding is thought to be a suitable method for joining dissimilar materials, such as aluminum to steel in multimaterial car-body manufacturing, but when it is combined with other joining methods, such as spot ... -
Modeling of Friction Self-Piercing Riveting of Aluminum to Magnesium
(The American Society of Mechanical Engineers (ASME), 2016)In recent years, higher requirements on vehicle performance and emission have been posing great challenges to lightweighting of vehicle bodies. Mixed use of lightweight materials, e.g., aluminum alloys and magnesium alloys, ... -
A Study of Build Edge Profile for Prediction of Surface Roughness in Fused Deposition Modeling
(The American Society of Mechanical Engineers (ASME), 2016)Surface roughness prediction studies in fused deposition modeling (FDM) process are usually based on a perimeter profile of each deposited layer. This study categorizes three types of build edge profile composed of perimeter, ... -
Numerical Simulation and Experimentation on Electrochemical Buffing
(The American Society of Mechanical Engineers (ASME), 2016)The electrochemical buffing (ECB) process primarily works on the principle of preferential dissolution by coupling of electrical, chemical, and mechanical actions. ECB is used to buff clean and hygienic nanoscale surface ... -
Predicting Subjective Responses From Human Motion: Application to Vehicle Ingress Assessment
(The American Society of Mechanical Engineers (ASME), 2016)The ease of entering a car is one of the important ergonomic factors that car manufacturers consider during the process of car design. This has motivated many researchers to investigate factors that affect discomfort during ... -
Modeling and Analysis of Five-Axis Milling Configurations and Titanium Alloy Surface Topography
(The American Society of Mechanical Engineers (ASME), 2016)Five-axis milling with a ball-end cutter is commonly used to generate a good surface finish on complex parts, such as blades or impellers made of titanium alloy. The five-axis milling cutting process is not straight forward; ... -
Predictive Modeling of Grinding Force Considering Wheel Deformation for Toric Fewer-Axis Grinding of Large Complex Optical Mirrors
(The American Society of Mechanical Engineers (ASME), 2016)Fewer-axis ultraprecision grinding has been recognized as an important means for manufacturing large complex optical mirrors. The research on grinding force is critical to obtaining a mirror with a high surface accuracy ... -
An Analytical Foundation for Optimal Compensation of Three-Dimensional Shape Deformation in Additive Manufacturing
(The American Society of Mechanical Engineers (ASME), 2016)Additive manufacturing (AM) or three-dimensional (3D) printing is a promising technology that enables the direct fabrication of products with complex shapes without extra tooling and fixturing. However, control of 3D shape ... -
A Generalized Feed-Forward Dynamic Adaptive Mesh Refinement and Derefinement Finite-Element Framework for Metal Laser Sintering—Part II: Nonlinear Thermal Simulations and Validations2
(The American Society of Mechanical Engineers (ASME), 2016)A novel multiscale thermal analysis numerical tool has been developed to address the micro–macro interactions involved in localized melting and sintering processes, such as laser sintering of metals exhibiting nonlinear ...