Journal of Applied Mechanics: Recent submissions
Now showing items 1241-1260 of 12181
-
Wrinkling of Functionally Graded Sandwich Structures Subject to Biaxial and In-Plane Shear Loads
(The American Society of Mechanical Engineers (ASME), 2017)Benefits of a functionally graded core increasing wrinkling stability of sandwich panels have been demonstrated in a recent paper (Birman, V., and Vo, N., 2017, “Wrinkling in Sandwich Structures With a Functionally Graded ... -
Effects of Thickness on the Responses of Piezoresponse Force Microscopy for Piezoelectric Film/Substrate Systems
(The American Society of Mechanical Engineers (ASME), 2017)Piezoresponse force microscopy (PFM) extends the conventional nano-indentation technique and has become one of the most widely used methods to determine the properties of small scale piezoelectric materials. Its accuracy ... -
Buckling of a Pressurized Hemispherical Shell Subjected to a Probing Force
(The American Society of Mechanical Engineers (ASME), 2017)We study the buckling of hemispherical elastic shells subjected to the combined effect of pressure loading and a probing force. We perform an experimental investigation using thin shells of nearly uniform thickness that ... -
Friction Effects on the Edge-of-Contact Stresses for Sliding Contact Between a Flat Punch With Rounded Corners and a Half Space
(The American Society of Mechanical Engineers (ASME), 2017)For the title problem, the punch is assumed to be pressed vertically into the horizontal upper surface of the half space, then slide horizontally sideways. A range of such configurations is identified that permit Shtaerman’s ... -
Passive Regulation of Thermally Induced Axial Force and Displacement in Microbridge Structures
(The American Society of Mechanical Engineers (ASME), 2017)The analytical model of a mechanism for regulating the thermally induced axial force and displacement in a fixed–fixed microbeam is presented in this article. The mechanism which consists of a set of parallel chevron beams ... -
Thermal Fluctuations as a Computational Microscope for Studying Crystalline Interfaces: A Mechanistic Perspective
(The American Society of Mechanical Engineers (ASME), 2017)Interfaces such as grain boundaries are ubiquitous in crystalline materials and have provided a fertile area of research over decades. Their importance stems from the numerous critical phenomena associated with them, such ... -
Concurrent Rupture of Two Molecular Bonds in Series: Implications for Dynamic Force Spectroscopy
(The American Society of Mechanical Engineers (ASME), 2017)The immobilization of receptor–ligand molecules in dynamic force spectroscopy (DFS) often relies on an extra noncovalent linkage to solid surfaces, resulting in two barrier-crossing diffusion processes in series and ... -
Vibration of Flexible Structures Under Nonlinear Boundary Conditions
(The American Society of Mechanical Engineers (ASME), 2017)The nonlinear response of a flexible structure, subjected to generally supported conditions with nonlinearities, is investigated for the first time. An analytical procedure is proposed first. Moreover, a simulation technique ... -
How to Realize Volume Conservation During Finite Plastic Deformation
(The American Society of Mechanical Engineers (ASME), 2017)Volume conservation during plastic deformation is the most important feature and should be realized in elastoplastic theories. However, it is found in this paper that an elastoplastic theory is not volume conserved if it ... -
A Model for the Mullins Effect in Multinetwork Elastomers
(The American Society of Mechanical Engineers (ASME), 2017)Double and triple network (TN) elastomers can be made by infusing monomers into a single network (SN) polymer, causing it to swell, and then polymerizing and cross-linking the monomers. The result is a double network (DN) ... -
Cylindrical Borehole Failure in a Transversely Isotropic Poroelastic Medium
(The American Society of Mechanical Engineers (ASME), 2017)Rocks underground often have pores and bedding planes, which are appropriate to be described by the transversely isotropic poroelastic constitutive model. Drilling boreholes in these rocks must be careful, since stresses ... -
Morphology of Voltage-Triggered Ordered Wrinkles of a Dielectric Elastomer Sheet
(The American Society of Mechanical Engineers (ASME), 2017)Wrinkles widely existing in sheets and membranes have attracted a lot of attention in the fields of material science and engineering applications. In this paper, we present a new method to generate ordered (striplike) and ... -
A Thin Elastic Membrane Conformed to a Soft and Rough Substrate Subjected to Stretching/Compression
(The American Society of Mechanical Engineers (ASME), 2017)Conformability of bio-integrated electronics to soft and microscopically rough biotissues can enhance effective electronics–tissue interface adhesion and can facilitate signal/heat/mass transfer across the interface. When ... -
Indentation of a Transversely Isotropic Thermoporoelastic Half-Space by a Rigid Circular Cylindrical Punch
(The American Society of Mechanical Engineers (ASME), 2017)Exact solutions to the three-dimensional (3D) contact problem of a rigid flat-ended circular cylindrical indenter punching onto a transversely isotropic thermoporoelastic half-space are presented. The couplings among the ... -
Thermomechanical Analysis of Epidermal Electronic Devices Integrated With Human Skin
(The American Society of Mechanical Engineers (ASME), 2017)Epidermal electronic devices (EEDs) are very attractive in applications of monitoring human vital signs for diagnostic, therapeutic, or surgical functions due to their ability for integration with human skin. Thermomechanical ... -
Meta-Atom Molecular Dynamics for Studying Material Property Dependent Deformation Mechanisms of Alloys
(The American Society of Mechanical Engineers (ASME), 2017)Massively parallel molecular dynamics (MD) simulations have been performed to understand the plastic deformation of metals. However, the intricate interplay between the deformation mechanisms and the various material ... -
Transient Response of MDOF Systems With Inerters to Nonstationary Stochastic Excitation
(The American Society of Mechanical Engineers (ASME), 2017)Explicit, closed-form, exact analytical expressions are derived for the covariance kernels of a multi degrees-of-freedom (MDOF) system with arbitrary amounts of viscous damping (not necessarily proportional-type), that is ... -
A Unique and Rational Applications Methodology for Fiber Composite Laminates
(The American Society of Mechanical Engineers (ASME), 2017)An applications methodology is synthesized from the research-based development of failure theory for orthotropic fiber composite laminates. In effect, this work continues and completes the work of Christensen (2017, ... -
Energy Exchange and Localization in Essentially Nonlinear Oscillatory Systems: Canonical Formalism
(The American Society of Mechanical Engineers (ASME), 2017)Over recent years, a lot of progress has been achieved in understanding of the relationship between localization and transport of energy in essentially nonlinear oscillatory systems. In this paper, we are going to demonstrate ... -
Riccati Transfer Matrix Method for Linear Tree Multibody Systems
(The American Society of Mechanical Engineers (ASME), 2017)The Riccati transfer matrix method (RTMM) improves the numerical stability of analyzing chain multibody systems with the transfer matrix method for multibody systems (MSTMM). However, for linear tree multibody systems, the ...