Journal of Applied Mechanics: Recent submissions
Now showing items 1041-1060 of 12181
-
An Acoustic-Microwave Method for the Study of the Mechanical Influence of Moisture Content in Materials
(The American Society of Mechanical Engineers (ASME), 2018)A one-dimensional theoretical model is developed to predict the acoustic waves generated by rapid thermal expansion caused by electromagnetic microwave absorption in viscoelastic rods. The theoretical acceleration at the ... -
On the Sufficient Symmetry Conditions for Isotropy of Elastic Moduli
(The American Society of Mechanical Engineers (ASME), 2018)The structural symmetry of a material can be manifested at a multitude of length scales such as spatial arrangement of atoms in a crystal structure, preferred orientation of grains in a polycrystalline material, alignment ... -
Effect of Cohesive Zone Size on Peeling of Heterogeneous Adhesive Tape
(The American Society of Mechanical Engineers (ASME), 2018)The interaction between the cohesive zone and the elastic stiffness heterogeneity in the peeling of an adhesive tape from a rigid substrate is examined experimentally and with finite element simulations. It is established ... -
Refined First-Order Shear Deformation Theory Models for Composite Laminates
(The American Society of Mechanical Engineers (ASME), 2018)In the present work, new mixed variational formulations for a first-order shear deformation laminate theory are proposed. The out-of-plane stresses are considered as primary variables of the problem. In particular, the ... -
A Modulated Voltage Waveform for Enhancing the Travel Range of Dielectric Elastomer Actuators
(The American Society of Mechanical Engineers (ASME), 2018)This paper presents a method to achieve high deformability levels in dielectric elastomer actuators (DEAs) by applying a modulated voltage waveform. The method relies on supplying the electrostatic energy during the specific ... -
A Higher-Order Theory for Open and Closed Curved Rods and Tubes Using a Novel Curvilinear Cylindrical Coordinate System
(The American Society of Mechanical Engineers (ASME), 2018)In this study, the governing equation of motion for a general arbitrary higher-order theory of rods and tubes is presented for a general material response. The impetus for the study, in contrast to the classical Cosserat ... -
Comparison of Double-Shearing and Coaxial Models for Pressure-Dependent Plastic Flow at Frictional Boundaries
(The American Society of Mechanical Engineers (ASME), 2018)The qualitative difference in solution behavior in the vicinity of maximum friction surfaces is demonstrated for two distinct models of pressure-dependent plasticity (the double-shearing and coaxial models) using closed-form ... -
Experimental Evaluation of Structural Intensity in Two-Dimensional Plate-Type Locally Resonant Elastic Metamaterials
(The American Society of Mechanical Engineers (ASME), 2018)Elastic metamaterials utilize locally resonant mechanical elements to onset band gap characteristics that are typically exploited in vibration suppression and isolation applications. The present work employs a comprehensive ... -
Stabilization Parameters and Smagorinsky Turbulence Model
(The American Society of Mechanical Engineers (ASME), 2018)For the streamline-upwind/Petrov-Galerkin and pressure-stabilizing/Petrov-Galerkin formulations for flow problems, we present in this paper a comparative study of the stabilization parameters defined in different ways. The ... -
Effective Electromechanical Properties of 622 Piezoelectric Medium With Unidirectional Cylindrical Holes
(The American Society of Mechanical Engineers (ASME), 2018)Diesel-natural gas dual fuel engine has gained increasing interesting in recent years because of its excellent power and economy. However, the reliability of the dual fuel engine does not meet the requirements of practical ... -
Analysis of Asymmetric Nonviscously Damped Linear Dynamic Systems
(The American Society of Mechanical Engineers (ASME), 2018)Multiple-degree-of-freedom linear asymmetric nonviscously damped systems are considered. It is assumed that the nonviscous damping forces depend on the past history of velocities via convolution integrals over exponentially ... -
A Semi-Infinite Strip Pressed Against an Elastic Half-Plane With Frictional Slip
(The American Society of Mechanical Engineers (ASME), 2018)The subject of this investigation is the plane strain elasticity problem of a finite width semi-infinite strip with its end pressed against a half-plane of the same material with friction. From the existing integral equation ... -
An Algorithm for Rigid-Body Angular Velocity and Attitude Estimation Based on Isotropic Accelerometer Strapdowns
(The American Society of Mechanical Engineers (ASME), 2018)A novel algorithm for the estimation of rigid-body angular velocity and attitude—the most challenging part of pose-and-twist estimation—based on isotropic accelerometer strapdowns, is proposed in this paper. Quaternions, ... -
Feedback Stabilization of Quasi-Integrable Hamiltonian Systems
(The American Society of Mechanical Engineers (ASME), 2018)A procedure for designing a feedback control to asymptotically stabilize with probability one quasi-integrable Hamiltonian system is proposed. First, a set of averaged Ito⁁ stochastic differential equations for controlled ... -
One-Dimensional Constrained Blister Test to Measure Thin Film Adhesion
(The American Society of Mechanical Engineers (ASME), 2018)A rectangular film is clamped at the opposite ends before being inflated into a blister by an external pressure, p. The bulging film adheres to a constraining plate with distance, w0, above. Increasing pressure expands the ... -
Anisotropic Mechanics of Cellular Substrate Under Finite Deformation
(The American Society of Mechanical Engineers (ASME), 2018)The use of cellular substrates for stretchable electronics minimizes not only disruptions to the natural diffusive or convective flow of bio-fluids, but also the constraints on the natural motion of the skin. The existing ... -
Interaction Model for “Shelled Particles” and Small-Strain Modulus of Granular Materials
(The American Society of Mechanical Engineers (ASME), 2018)The elastic modulus of a granular assembly composed of spherical particles in Hertzian contact usually has a scaling law with the mean effective pressure p as K∼G∼p1/3. Laboratory test results, however, reveal that the ... -
The Energy Absorption Behavior of Cruciforms Designed by Kirigami Approach
(The American Society of Mechanical Engineers (ASME), 2018)The cruciforms are widely employed as energy absorbers in ships and offshore structures, or basic components in sandwich panel and multicell structure. The kirigami approach is adopted in the design of cruciform in this ... -
Extended Greenwood–Williamson Models for Rough Spheres
(The American Society of Mechanical Engineers (ASME), 2018)The current work aims to develop two extended Greenwood–Williamson (GW) models for spherical particles with surface roughness which can be incorporated into the discrete element modeling (DEM) framework. The defects of the ... -
A Method for Particle Simulation
(The American Society of Mechanical Engineers (ASME), 2018)This paper extends a recent approach to the direct numerical simulation of particle flows to the case in which the particles are not fixed. The basic idea is to use a local analytic representation valid near the particle ...