Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3901-3920 of 4506
-
Some Considerations on Estimation of Energy Release Rates for Circumferentially Cracked Pipes
(The American Society of Mechanical Engineers (ASME), 1984)The estimation of energy release rates under multiple loading conditions is discussed from the viewpoint of variation of the potential energy of the nonlinear elastic cracked body. Applications ... -
Two-Phase Flow and Water Hammer Loads in Vessels, Piping and Structural Systems (PVP Special Publication, Vol. 91)
(The American Society of Mechanical Engineers (ASME), 1984) -
Thermal Stresses in U-Tubes Versus Bend Radius and Baffle Spacings
(The American Society of Mechanical Engineers (ASME), 1984)Analytical and explicit formulas are developed to give maximum rotation, bending moment and stress in heat exchanger U-tubes due to the difference between thermal expansions of hot leg and cold ... -
Earthquake Source Modeling, Ground Motion, and Structural Response (PVP Special Publication, Vol. 80)
(The American Society of Mechanical Engineers (ASME), 1984) -
Ductile Fracture of Circumferentially Cracked Type-304 Stainless Steel Pipes in Tension
(The American Society of Mechanical Engineers (ASME), 1984)Circumferentially cracked pipes subjected to tensile load were analyzed for finite length and constant depth part-through cracks located at the inside of the pipe wall. The analysis postulated ... -
Stochastic Simulation of PWR Vessel Integrity for Pressurized Thermal Shock Conditions
(The American Society of Mechanical Engineers (ASME), 1984)A stochastic simulation methodology is presented for performing probabilistic analyses of Pressurized Water Reactor vessel integrity. Application of the methodology to vessel-specific integrity ... -
Seismic and Dynamic Analysis Methods (PVP Special Publication, Vol. 81)
(The American Society of Mechanical Engineers (ASME), 1984) -
Tubesheet Thicknesses and Tube Loads for Floatinghead and Fixed-Tubesheet Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 1984)This paper presents procedures for computing tubesheet thicknesses and tube loads for floatinghead and fixed-tubesheet heat exchangers. It was prepared in connection with the activities of the ... -
A Method for In Situ Test and Analysis of Nuclear Plant Equipment
(The American Society of Mechanical Engineers (ASME), 1984)Requalification of equipment in operating nuclear power plants to present-day criteria can be an expensive undertaking; however in situ measurements and data analysis procedures can be used to ... -
In-Plane Bending Behavior of Pipe Bends With End Constraints Under Steady-State Creep
(The American Society of Mechanical Engineers (ASME), 1984)This paper presents an analysis for the in-plane bending behavior of smooth thin pipe bends connected to tangent pipes or rigid flanges under steady-state creep conditions. Creep flexibility ... -
Cyclic Plastic Deformation of a Circular Plate With Work Hardening
(The American Society of Mechanical Engineers (ASME), 1984)An experimental and theoretical study was performed of the nonlinear behavior of a simply supported flat circular aluminum plate under reversed cyclic central load. The application is for the ... -
The Influence of Residual Stresses on Small Through-Clad Cracks in Pressure Vessels
(The American Society of Mechanical Engineers (ASME), 1984)The influence of cladding residual stresses on the crack driving force for shallow cracks in the wall of a nuclear pressure vessel is investigated. Thermo-elastic-plastic analyses were carried ... -
Implication of Elastic Stress Range at Structural Discontinuity
(The American Society of Mechanical Engineers (ASME), 1984)This paper illustrates that in addition to the elastic stress intensity range it is necessary to evaluate the stress intensities (and corresponding material properties) at specific times during ... -
Plastic Strain Energy in Fatigue Failure
(The American Society of Mechanical Engineers (ASME), 1984)In this paper the cyclic plastic strain energy of the A-516 Gr. 70 carbon low-alloy steel during fully reversed constant strain or stress-controlled cycles is discussed. A relationship is ... -
An Exact Modal Analysis of the Static Deformation of Long Cylinders and Rings
(The American Society of Mechanical Engineers (ASME), 1984)This paper presents a static, modal solution of Flugge’s thin shell equations for the cases of a ring or a long cylinder in a state of plane strain. The solution derived here enables the ... -
The Velocity of Missiles Generated by the Disintegration of Gas-Pressurized Vessels and Pipes
(The American Society of Mechanical Engineers (ASME), 1984)A theoretical model is developed to describe the velocity of fragments generated when a gas-pressurized vessel disintegrates. The predictions are compared with new and existing experimental data ... -
A Reassessment of PWR Pressure Vessel Integrity During Overcooling Accidents, Considering 3-D Flaws
(The American Society of Mechanical Engineers (ASME), 1984)A continuing analysis of the pressurized-thermal-shock problem associated with PWR postulated overcooling accidents indicates that the previously accepted degree of conservatism in the fracture-mechanics ... -
Curvatures and Membrane Stresses in Pressure Vessel Heads
(The American Society of Mechanical Engineers (ASME), 1984)In this paper, the membrane stresses induced in axisymmetrical shells subjected to internal loading are analyzed in the light of curvatures. This approach enables a deeper understanding of the ... -
Efficient Computational Procedures for Long-Time Duration Fluid-Structure Interaction Problems
(The American Society of Mechanical Engineers (ASME), 1984)In this paper, two different classes of transient algorithms, implicit-explicit and implicit-implicit, are developed for the response calculations of long-time duration fluid structure interaction ... -
Design of Elevated Temperature Piping (PVP Special Publication, Vol. 86)
(The American Society of Mechanical Engineers (ASME), 1984)