Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3881-3900 of 4506
-
Evaluation of the Growth and Stability of Stress Corrosion Cracks in Sensitized Austenitic Piping
(The American Society of Mechanical Engineers (ASME), 1984)This paper presents the results of a research program conducted to evaluate the behavior of stress corrosion cracks in sensitized austenitic piping exposed to high temperature, high purity ... -
Stiffening Effects of Tubes in Heat Exchanger Tubesheet
(The American Society of Mechanical Engineers (ASME), 1984)Strain-measuring tests were performed with strain gages on rectangular coupons taken from perforated plate with triangular pitch under both uniaxial tensile loads and pure bending loads. The ... -
Accurate Treatment of Material Interface Dynamics in the Calculation of One-Dimensional Two-Phase Flows by the Integral Method of Characteristics
(The American Society of Mechanical Engineers (ASME), 1984)Accurate numerical methods for treating the junction and boundary conditions needed in the transient two-phase flows of a piping network were published earlier by us; the same methods are used ... -
Consistent Hydrodynamic Mass for Parallel Prismatic Beams in a Fluid-Filled Container
(The American Society of Mechanical Engineers (ASME), 1984)In this paper, representation of the effects of incompressible fluid on the dynamic response of parallel beams in fluid-filled containers is developed using the concept of hydrodynamic mass. ... -
Fatigue Crack Growth in Large Specimens With Various Stress Ratios
(The American Society of Mechanical Engineers (ASME), 1984)An experimental investigation has been carried out on large plates made of pressure vessel steel A516 Gr.70, to determine the fatigue crack growth rate. The specimen size was 914.4 × 304.8 ... -
On Design Procedures for the Buckling of Cylinders Under Combined Axial Compression and External Pressure
(The American Society of Mechanical Engineers (ASME), 1984)The test results on biaxially compressed metallic cylinders published before 1983, together with some early ones from a test program underway at Liverpool University, were plotted in terms of ... -
The Challenge of Continuous Flaw Monitoring in Electric Utility Practice
(The American Society of Mechanical Engineers (ASME), 1984) -
Structural Evaluation of a Butt-Welded Elbow End: A Simplified Procedure
(The American Society of Mechanical Engineers (ASME), 1984)Explicit piping design procedures are not provided in theASME Code for structural evaluation of ovalization and fabrication effects at the butt-welded end of an elbow. This paper presents a ... -
Elastic-Plastic Analyses of Surface Flaws in a Reactor Vessel
(The American Society of Mechanical Engineers (ASME), 1984)Elastic-plastic analyses have been performed for the ASME Maximum Postulated Flaw and for three other semielliptical surface flaws in the beltline region of a nuclear reactor pressure vessel, ... -
Pipe Whip Considerations for Design of Nozzles
(The American Society of Mechanical Engineers (ASME), 1984)Effects of pipe breaks on nozzle design have been considered in this paper. Simple methods have been used for estimating the maximum possible pipe whip loads for design of nozzles and other ... -
The Technical Basis of the External Pressure Section of BS5500
(The American Society of Mechanical Engineers (ASME), 1984)The technical basis of the external pressure section of the British Pressure Vessel Code BS5500 is presented. Interstiffener collapse of cylinders, overall collapse, sideways tripping of stiffeners ... -
Isentropic Expansion of Dry Saturated Vapor—Application to the Design of Safety Valves
(The American Society of Mechanical Engineers (ASME), 1984)Accepted standards relative to the design of safety valves are based on calculations of the maximum (flow rate) during isentropic expansion through a converging nozzle. The theoretical value is ... -
On the Determination of the Propagation Pressure of Long Circular Tubes
(The American Society of Mechanical Engineers (ASME), 1984)A propagating buckle can be initiated in tubes under external pressure from localized imperfections. Once initiated a buckle will propagate with the result of flattening the tube behind it. The ... -
Transient Creep Equation of Polymeric Materials Based on Tensor Function Theory and Its Experimental Evaluation
(The American Society of Mechanical Engineers (ASME), 1984) -
Recent Advances in Nuclear Component Testing and Theoretical Studies on Buckling (PVP Special Publication, Vol. 89)
(The American Society of Mechanical Engineers (ASME), 1984) -
Letter to the Editor commenting on “Maximum Stresses and Flexibility Factors of Smooth Pipe Bends With Tangent Pipe Terminations Under In-Plane Bending” (Thomson, G., and Spence, J., 1983, ASME J. Pressure Vessel Technol., 105, p. 329)
(The American Society of Mechanical Engineers (ASME), 1984) -
Stable Growth and Instability of Circumferential Cracks in Type 304 Stainless Steel Pipes Under Tensile Load
(The American Society of Mechanical Engineers (ASME), 1984)Flaws due to stress corrosion cracking have frequently been found in Type 304 stainless steel piping of some boiling water reactor (BWR) plants. In this work, in order to quantitatively examine ... -
Computational Fracture Mechanics—Nonlinear and 3-D Problems (PVP Special Publication, Vol. 85)
(The American Society of Mechanical Engineers (ASME), 1984) -
Lowest Natural Frequencies of Multiply Supported U-Tubes
(The American Society of Mechanical Engineers (ASME), 1984) -
Bend and Adjacent Span Reduction Factors
(The American Society of Mechanical Engineers (ASME), 1984)A semi-analytical and computer experimental procedure is described for developing the bend and adjacent span reduction factors for an alternate method of seismic restraint spacing, based on stress ...