Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3361-3380 of 4506
-
Rectangular Pressure Vessels of Finite Length
(The American Society of Mechanical Engineers (ASME), 1990)Design Rules in the ASME Code, Section VIII, Division 1, cover the design of unreinforced and reinforced rectangular pressure vessels. These rules are based on “infinitely long” vessels of ... -
Thermoelastoplastic and Residual Stresses in a Hollow Cylinder With Temperature-Dependent Properties
(The American Society of Mechanical Engineers (ASME), 1990)Determination of residual stresses and the positive or negative effect that they may have on the component is an important consideration in design. Unexpected failure of components, latter ... -
Flow-Induced Vibration of Rod Arrays in a Jet Flow
(The American Society of Mechanical Engineers (ASME), 1990)Flow-induced vibration of rod arrays in a jet flow was studied experimentally. The rod arrays tested were on square layout with a pitch-to-diameter ratio of 1.32. The rods were found to vibrate ... -
Nonlinear Analysis of Steel Liner—Reinforced Concrete Penstocks
(The American Society of Mechanical Engineers (ASME), 1990)This paper is concerned with the nonlinear structural responses of steel liner-reinforced concrete penstocks of a concrete dam subjected to an internal pressure. The study reported herein consists ... -
Dynamic Response Studies of Piping-Support Systems
(The American Society of Mechanical Engineers (ASME), 1990)Considering the effect of the interaction between piping and support systems in the piping design is a more integrated approach to improve the reliability of piping systems. So, it is important ... -
Response Characteristics of Piping System Supported by Visco-Elastic and Elasto-Plastic Dampers
(The American Society of Mechanical Engineers (ASME), 1990)Improving the reliability of the piping systems can be achieved by eliminating the mechanical snubber and by reducing the response of the piping. In the seismic design of piping system, damping ... -
Weight Analysis of Thin-Walled Ellipsoidal Shells
(The American Society of Mechanical Engineers (ASME), 1990) -
An Interpretation of Axial Creep-Fatigue Damage Interaction in Type 316 Stainless Steel (Survey Paper)
(The American Society of Mechanical Engineers (ASME), 1990)Creep-fatigue interaction and its effect on damage of components in service have been a major concern to analysts. To deal with this problem, several criteria have been proposed and used, such ... -
Titanium-Jacketed Cannon Tube Technology
(The American Society of Mechanical Engineers (ASME), 1990) -
Random Vibrations
(The American Society of Mechanical Engineers (ASME), 1990) -
Life Assessment of Hot Reheat Steam Pipe
(The American Society of Mechanical Engineers (ASME), 1990)A methodology for assessing the remaining life of hot reheat steam pipe with longitudinal flaws, such as those typically associated with the longitudinal seam welds, has been developed. The ... -
Analysis of a Three-Dimensional Tank-Liquid-Soil Interaction Problem
(The American Society of Mechanical Engineers (ASME), 1990)A three-dimensional analysis of the dynamic behavior of liquid-filled elastic cylindrical tanks based on flexible grounds, undergoing horizontal and vertical earthquake excitation is presented. The ... -
Simplified Models for the Dynamic Response of Tall Unanchored Liquid Containers
(The American Society of Mechanical Engineers (ASME), 1990)Two simplified models are presented for determining the hydrodynamic loads developed during the seismic response of tall unanchored liquid storage tanks. In both models the general procedure ... -
Fatigue Crack Growth: A Case Study of Synthetic Tower Spectrum Loading
(The American Society of Mechanical Engineers (ASME), 1990)Hourly pressure variations were recorded during six years in two synthetic towers, giving a total of 105,000 readings. The readings were converted into a 15-block pressure amplitude spectrum of ... -
Residual Stresses in Inconel 600 U-Bend Heat Exchanger Tubes
(The American Society of Mechanical Engineers (ASME), 1990) -
Growth of Buckling Instabilities During Radial Collapse of a Ring
(The American Society of Mechanical Engineers (ASME), 1990)Conditions leading to the growth of initial imperfections for rings or long cylindrical shells subjected to initial uniform inward impulsive velocity loading are investigated. The work is motivated ... -
Computational and Experimental Analysis of Stress Concentrations in Pressure Vessel Cascades
(The American Society of Mechanical Engineers (ASME), 1990) -
A Phenomenological Description on Thermomechanical Behavior of Shape Memory Alloys
(The American Society of Mechanical Engineers (ASME), 1990) -
60th Birthday of JPVT Associate Technical Editor Karl Kussmaul
(The American Society of Mechanical Engineers (ASME), 1990) -
A Finite Element Technique for Limit Analysis of Structures
(The American Society of Mechanical Engineers (ASME), 1990)Limit analysis provides an alternative to incremental elastic-plastic analysis for determining a limit load. The limit load is obtained from the lower and upper-bound theorems. These theorems, ...