Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3341-3360 of 4506
-
Fatigue Life Prediction of an Autofrettaged Thick-Walled Pressure Vessel With an External Groove
(The American Society of Mechanical Engineers (ASME), 1991)An autofrettaged thick-walled pressure vessel with an external groove subjected to a pulsating internal pressure can have fatigue failures at the external groove root due to the combination of ... -
A Simple Model for Fatigue Crack Growth Near Stress Concentrations
(The American Society of Mechanical Engineers (ASME), 1991)Fatigue crack growth rates are often difficult to predict for short cracks growing near stress concentrations. This paper presents a simple model to predict those growth rates which incorporates ... -
Creep-Fatigue Strength of Long-Term Post-Service 2 · 1/4 Cr-1 · Mo Steel and Remaining Life Estimation
(The American Society of Mechanical Engineers (ASME), 1991)Creep-fatigue strength of post-service 2 · 1/4 Cr-1 · Mo steel used for about one hundred-thousand hours in a fossil fuel power plant was studied. The creep-fatigue strength of the ... -
Failure Probability Analysis for a Cylinder Subjected to General Loading Conditions
(The American Society of Mechanical Engineers (ASME), 1991)This paper studies stresses and failure probabilities for a cylinder subjected to different combinations of inner pressure, outer pressure, axial load, torque, and thermal loading. Probabilistic ... -
An Analysis of High-Temperature Crack Growth in Type 308 Cb Stainless Steel and Its Weldment
(The American Society of Mechanical Engineers (ASME), 1991)Creep crack growth behavior of type 308 Cb austenitic stainless steel and its weldment has been studied in the temperature range of 875 to 1075 K under plane stress condition. The creep crack ... -
Parametric Resonance of Liquid Storage Axisymmetric Shell Under Horizontal Excitation
(The American Society of Mechanical Engineers (ASME), 1991)A procedure for analyzing parametric resonance of liquid storage axisymmetric shells is proposed that is an extension of the procedure presented at PVP-89 for parametric resonance of empty ... -
Effect of Hydrostatic Retest on the Fatigue Behavior of a Steel Gas Cylinder
(The American Society of Mechanical Engineers (ASME), 1991)Retardation effect of the hydrostatic test on the subsequent crack growth in an AISI 4130X steel gas cylinder has been predicted. The post-test retardation period depends upon the size of the ... -
Impulsive Responses of a Circular Cylindrical Shell Subjected to Waterhammer Waves
(The American Society of Mechanical Engineers (ASME), 1991)The impulsive responses of semi-finite and finite pipes filled with fluid are analyzed in order to clarify the validity of Joukowsky’s theory and the fluid-pipe coupling effect. In the analysis, ... -
Response Analysis of Secondary Systems With Nonlinear Supports
(The American Society of Mechanical Engineers (ASME), 1991)This paper introduces a simplified random vibrations analysis method of linear secondary systems with nonlinear supports. The method separates, as much as possible, the nonlinear analysis of the ... -
Stress Classification for Elevated Temperature Service
(The American Society of Mechanical Engineers (ASME), 1991)The paper presents two procedures which can be used to classify the stresses originating at the structural discontinuities of pressure vessel and piping components designed for elevated temperature ... -
The ASME Code and 3D Stress Evaluation
(The American Society of Mechanical Engineers (ASME), 1991)The ASME Code [1] identifies the modes of failure that must be addressed to ensure acceptable pressure vessel designs. The failure modes addressed in this paper are precluded by limits on the ... -
Simplified Dynamic Analysis Methods for Metallic Bellows Expansion Joints
(The American Society of Mechanical Engineers (ASME), 1991)An investigation into dynamic characteristics and seismic response of bellows expansion joints is described. For axial and lateral vibrations of the bellows, simplified methods are developed to ... -
A Stress Analysis of Pipe Flange Connections
(The American Society of Mechanical Engineers (ASME), 1991)The use of pipe flange connections is standardized in the codes of JIS, ASME, DIN and so on. However, these codes are almost entirely dependent on experience, and subsequently some problems ... -
Stresses in Thick Pressure Vessel Heads
(The American Society of Mechanical Engineers (ASME), 1990)The finite element method is used to study stresses in two types of spherical pressure vessel heads having very wide range of applications in industries. The first problem involves a nozzle ... -
Dynamic Response of Sandwich Shells of Revolution
(The American Society of Mechanical Engineers (ASME), 1990)Development of an annular finite element, for the linear elastic analysis of sandwich shells, is reported here. The derivation of stiffness and mass matrices is based on improved shell theory ... -
Large-Amplitude Sloshing With Submerged Blocks
(The American Society of Mechanical Engineers (ASME), 1990)The computer simulation of forced vibrations induced on a water pool is presented in this paper. The complexity of the seismic fluid-structure interaction problem is accentuated by the large ... -
Long-Term Creep Curve Prediction Based on the Modified θ Projection Concept
(The American Society of Mechanical Engineers (ASME), 1990) -
Thermal Ratcheting Criteria and Behavior of Piping Elbows
(The American Society of Mechanical Engineers (ASME), 1990)A thermal ratcheting test was performed using an elbow model test specimen subjected to sustained primary load and cyclic thermal transient strains. Under severe loading conditions incremental ... -
A Simplified Axisymmetric Analysis of Steel Containment Under General Dynamic Pressure
(The American Society of Mechanical Engineers (ASME), 1990)Loadings to cause severe accidents on containment buildings can include combinations of uniform internal pressure, dynamic pressure, and seismic. Most studies that have been conducted to predict ... -
Three-Dimensional Finite Element Analysis of Temperatures and Stresses in a Single-Pass Butt-Welded Pipe
(The American Society of Mechanical Engineers (ASME), 1990)Temperatures, stresses, and deformations in a single-pass butt-welded pipe are studied with a full three-dimensional finite element model. The model covers the whole circumference and the complete ...