Journal of Engineering for Gas Turbines and Power: Recent submissions
Now showing items 2681-2700 of 9564
-
Discussion: “Effectiveness and Heat Transfer With Full-Coverage Film” (Metzger, D. E., Takeuchi, D. I., and Kuenstler, P. A., 1973, ASME J. Eng. Power, 95, pp. 180–184)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Further Development of the Burning Profile” (Wagoner, C. L., and Winegartner, C. E., 1973, ASME J. Eng. Power, 95, pp. 119–123)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Performance of Perforated Heat Exchanger Surfaces” (Mondt, J. R., and Siegla, D. C., 1974, ASME J. Eng. Power, 96, pp. 81–86)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “An Experimental Correlation of Oxides of Nitrogen Emissions from Power Boilers Based on Field Data” (Rawdon, A. H., and Sadowski, R. S., 1973, ASME J. Eng. Power, 95, pp. 165–170)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Perspectives for Waste Heat Recovery by Means of Organic Fluid Cycles” (Angelino, G., and Moroni, V., 1973, ASME J. Eng. Power, 95, pp. 75–83)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Protection of Boiler Feed Pump Against Transient Suction Pressure Decay” (Liao, G. S., 1974, ASME J. Eng. Power, 96, pp. 247–254)
(The American Society of Mechanical Engineers (ASME), 1974) -
Operational Limits for Gas Turbine Compressors During Transient Conditions in a Helium Cooled Reactor
(The American Society of Mechanical Engineers (ASME), 1974)The use of gas turbines in Gas Cooled Fast Reactors requires an accurate analysis of the loss of pressure accident induced by the rupture of a main helium pipe. In this paper a multiloop ... -
Ensuring Stable Circuit Conditions of Direct Cycle Helium Gas Turbine System
(The American Society of Mechanical Engineers (ASME), 1974)The choice of compressor characteristics of turbogroups is of decisive importance for the stable behavior of circuits during transients. It is shown how compressor surge at dangerous speeds ... -
A Generalized Discharge Coefficient for Differential Pressure Type Fluid Meters
(The American Society of Mechanical Engineers (ASME), 1974)A generalized rational equation is derived for the discharge coefficient of differential pressure-type fluid meters. Its factors are particularized for throat tap meters, pipe wall tap nozzles, ... -
Discussion: “Some Comparison of Simultaneous Stack Gas Particulate Determinations Using the ASME and EPA Method” (Selle, S. J., and Gronhovd, G. H., 1973, ASME J. Eng. Power, 95, pp. 145–149)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “ASME Steam Turbine Code Test Using Radioactive Tracers” (Cotton, K. C., Schofield, P., and Herzog, W. G., 1973, ASME J. Eng. Power, 95, pp. 155–164)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Analysis of Power Plant Deaerators Under Transient Turbine Loads” (Liao, G. S., 1973, ASME J. Eng. Power, 95, pp. 171–179)
(The American Society of Mechanical Engineers (ASME), 1974) -
Lift and Moment Prediction For an Oscillating Airfoil With a Moving Separation Point
(The American Society of Mechanical Engineers (ASME), 1974)An analytical method for predicting the perturbed aerodynamic reactions of a harmonically oscillating flat plate airfoil with time dependent point of separation is presented. It is shown that ... -
End-Wall Boundary Layers in Axial Compressors
(The American Society of Mechanical Engineers (ASME), 1974)Various aspects of an end-wall boundary-layer theory in axial compressors, as formulated originally by Mellor and Wood, are analyzed. This analysis contains three parts. In the first part the ... -
Supersonic Unstalled Flutter In Fan Rotors; Analytical and Experimental Results
(The American Society of Mechanical Engineers (ASME), 1974)Supersonic unstalled flutter is predicted using an unsteady supersonic cascade analysis, a cascade wind tunnel and a high speed fan rotor. Since the unsteady analysis assumes thin flat plate ... -
Calculation of Cascade Profiles From the Velocity Distribution
(The American Society of Mechanical Engineers (ASME), 1974)The method using the properties of analytical functions is applied to a plane, steady, inviscid, everywhere subsonic flow. From data fixed a priori concerning the external flow and some details ... -
The M.I.T. Blowdown Compressor Facility
(The American Society of Mechanical Engineers (ASME), 1974)A Blowdown Compressor Test Facility has been developed which allows time resolved aerodynamic testing of full-scale transonic compressor rotors at low cost. The rotor is brought to speed in ... -
Premixed Combustion in a Baffle Combustor and the Effect of Steam Injection
(The American Society of Mechanical Engineers (ASME), 1974)Details are given of the operation of a 90 deg annular sector of a ceramic-lined baffle-type combustor utilising premixed propane/air or propane/air/steam composition at ambient inlet conditions. ... -
Highlights and Future Development of Closed-Cycle Gas Turbines
(The American Society of Mechanical Engineers (ASME), 1974)At the moment the closed-cycle gas turbine attracts considerable attention due to: 1 The possibility of directly coupling the closed-cycle gas turbine with a gas-cooled high temperature reactor; ... -
Similarity Parameters for Comparing Erosive Particle Trajectories in Hot Air and Cold Air Radial Inflow Turbines
(The American Society of Mechanical Engineers (ASME), 1974)The similarity parameters that can be used to relate erosive particle trajectories in hot gas and equivalent cold gas flows are derived from the equations of motion. The flow in a radial ...