Journal of Engineering for Gas Turbines and Power: Recent submissions
Now showing items 2661-2680 of 9564
-
A Probabilistic Approach to Safety System Testing and Maintenance
(The American Society of Mechanical Engineers (ASME), 1974)This paper presents a method to quantify in terms of probabilistic availability the effects of testing and maintenance schedule on the performance of a standby safety system and it describes ... -
Acoustic Characteristics of a Gas Turbine Exhaust Model
(The American Society of Mechanical Engineers (ASME), 1974)To investigate the sources of acoustic radiation from a gas turbine exhaust, a one-seventh scale model has been constructed. The model geometrically scales the flow path downstream of the ... -
Vibrations and Stability of Turbine Blades at Stall
(The American Society of Mechanical Engineers (ASME), 1974)A method is given for analyzing the vibrations of turbine blades subjected to flows at high negative incidence angles. The conditions for the existence of self-excited vibrations and the stability ... -
Corrosion and Deposits From Combustion of Solid Waste: Part 2—Chloride Effects on Boiler Tube and Scrubber Metals
(The American Society of Mechanical Engineers (ASME), 1974)Chlorides play an important role in corrosion of heat-transfer surfaces and wet-scrubbers in municipal incinerators. The nature of the deposits and the extent of corrosion have been investigated ... -
Conversion of Fuel Nitrogen to NOx in a Compact Combustor
(The American Society of Mechanical Engineers (ASME), 1974)A low-nitrogen fuel, ASTM Jet A aviation kerosene, was doped with increasing amounts of pyridine as a means of increasing the content of chemically bound nitrogen, then burned at a rate of ... -
Criteria for Electrostatic Collection of Unfavorable Ducts
(The American Society of Mechanical Engineers (ASME), 1974) -
Drainage Systems for Condensation
(The American Society of Mechanical Engineers (ASME), 1974)Efficient condensing surfaces are highly desirable in the design of solar sea power plants utilizing the ocean temperature difference. This paper examines a number of surface designs and presents ... -
Power Reduction in Air Conditioning by Means of Off-Peak Operation and Coolness Storage
(The American Society of Mechanical Engineers (ASME), 1974)An original air-conditioning system was developed which requires considerably less power than conventional systems while providing identical cooling and dehumidification. The 50 percent (depending ... -
Hydrodynamic Stability and Thermal Performance Test of a 1-MWt Sodium-Heated Once-Through Steam Generator Model
(The American Society of Mechanical Engineers (ASME), 1974)The 1-MWt Heat Transfer Model (HTM-1) test program was directed to the development of techniques to predict, and thereby avoid, water-side instabilities in sodium-heated once-through and recirculating ... -
Constant Failure Rate of Redundant Repairable Hardware
(The American Society of Mechanical Engineers (ASME), 1974)The objective of this paper is to investigate the nature of the failure rates of redundant repairable hardware. The analysis considers the case of two nominally identical, functionally independent ... -
Discussion: “A Wake and an Eddy in a Rotating Radial Flow Passage—Part I: Experimental Observations; Part II: Flow Model” (Moore, J., 1973, ASME J. Eng. Power, 95, pp. 205–219)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Evaluation of Silicon and Magnesium Silicon as Corrosion Inhibitors” (May, W. R., Zetlneisl, M. J., and Annand, R. R., 1974, ASME J. Eng. Power, 96, pp. 124–128)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “On the Unsteady Supersonic Cascade With a Subsonic Leading Edge” (Kurosaka, M., 1974, ASME J. Eng. Power, 96, pp. 13–31)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Calculation of Temperature Distribution in Multistage Axial Gas Turbine Rotor Assemblies When Blades are Uncooled” (Evans, D. M., 1973, ASME J. Eng. Power, 95, pp. 309–318)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Investigation of the Aerodynamic Performance of Small Axial Turbines” (Ewen, J. S., Huber, F. W., and Mitchell, J. P., 1973, ASME J. Eng. Power, 95, pp. 326–332)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Effect of Rotor Design Tip Speed on Aerodynamic Performance of a Model VTOL Lift Fan Under Static and Crossflow Conditions” (Stockman, N. O., Loeffler, I. S., and Liebein, S., 1973, ASME J. Eng. Power, 95, pp. 293–300)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Low Emissions Combustion for the Regenerative Gas Turbine, Parts 1 and 2” (Wade, W. R., Shen, P. I., Owens, C. W., and McLean, A. F., 1974, ASME J. Eng. Power, 96, pp. 32–55)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “The Use of a Hybrid Computer in the Optimization of Gas Turbine Control Parameters” (Saravanamuttoo, H. I. H., and MacIsaac, B. D., 1973, ASME J. Eng. Power, 95, pp. 257–264)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Some Effects of Variable Surface Temperature on Heat Transfer to a Partially Porous Flat Plate” (Nealy, D. A., 1973, ASME J. Eng. Power, 95, pp. 319–325)
(The American Society of Mechanical Engineers (ASME), 1974) -
Discussion: “Calculation of Compressible Subsonic Flow in Cascades With Varying Blade Height” (Van den Braembussche, R. A., 1973, ASME J. Eng. Power, 95, pp. 345–351)
(The American Society of Mechanical Engineers (ASME), 1974)