Geometric Optimization of C Shaped Cavities According to Bejan's Theory: General Review and Comparative StudySource: Journal of Electronic Packaging:;2013:;volume( 135 ):;issue: 003::page 31007DOI: 10.1115/1.4024113Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: The aim of this paper is to consider, by means of the numerical investigation, the geometric optimization of a cavity that intrudes into a solid with internal heat generation. The objective is to minimize the maximal dimensionless excess of temperature between the solid and the cavity. The cavity is rectangular, with fixed volume and variable aspect ratio. The cavity shape is optimized for two sets of boundary conditions: isothermal cavity and cavity cooled by convection heat transfer. The optimal cavity is the one that penetrates almost completely the conducting wall and proved to be practically independent of the boundary thermal conditions, for the external ratio of the solid wall smaller than 2. As for the convective cavity, it is worthy to know that for values of H/L greater than 2, the best shape is no longer the one that penetrates completely into the solid wall, but the one that presents the largest cavity aspect ratio H0/L0. Finally, when compared with the optimal cavity ratio calculated for the isothermal Cshaped square cavity, the cavities cooled by convection highlight almost the same optimal shape for values of the dimensionless group خ»â€‰â‰¤â€‰0.01. Both cavities, isothermal and cooled by convection, also present similar optimal shapes for د•0 < 0.3 and د•0 > 0.7. However, in the range 0.3 ≤ د•0 ≤ 0.7, the ratio (H0/L0)opt calculated for the cavities cooled by convection is greater than the one presented by isothermal cavities. This difference is approximately 17% when خ»â€‰= 0.1 and د•0 = 0.7, and 20% for خ»â€‰= 1 and د•0 = 0.5.
|
Collections
Show full item record
| contributor author | Lorenzini, G. | |
| contributor author | Biserni, C. | |
| contributor author | Rocha, L. A. O. | |
| date accessioned | 2017-05-09T00:57:44Z | |
| date available | 2017-05-09T00:57:44Z | |
| date issued | 2013 | |
| identifier issn | 1528-9044 | |
| identifier other | ep_135_03_031007.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/151438 | |
| description abstract | The aim of this paper is to consider, by means of the numerical investigation, the geometric optimization of a cavity that intrudes into a solid with internal heat generation. The objective is to minimize the maximal dimensionless excess of temperature between the solid and the cavity. The cavity is rectangular, with fixed volume and variable aspect ratio. The cavity shape is optimized for two sets of boundary conditions: isothermal cavity and cavity cooled by convection heat transfer. The optimal cavity is the one that penetrates almost completely the conducting wall and proved to be practically independent of the boundary thermal conditions, for the external ratio of the solid wall smaller than 2. As for the convective cavity, it is worthy to know that for values of H/L greater than 2, the best shape is no longer the one that penetrates completely into the solid wall, but the one that presents the largest cavity aspect ratio H0/L0. Finally, when compared with the optimal cavity ratio calculated for the isothermal Cshaped square cavity, the cavities cooled by convection highlight almost the same optimal shape for values of the dimensionless group خ»â€‰â‰¤â€‰0.01. Both cavities, isothermal and cooled by convection, also present similar optimal shapes for د•0 < 0.3 and د•0 > 0.7. However, in the range 0.3 ≤ د•0 ≤ 0.7, the ratio (H0/L0)opt calculated for the cavities cooled by convection is greater than the one presented by isothermal cavities. This difference is approximately 17% when خ»â€‰= 0.1 and د•0 = 0.7, and 20% for خ»â€‰= 1 and د•0 = 0.5. | |
| publisher | The American Society of Mechanical Engineers (ASME) | |
| title | Geometric Optimization of C Shaped Cavities According to Bejan's Theory: General Review and Comparative Study | |
| type | Journal Paper | |
| journal volume | 135 | |
| journal issue | 3 | |
| journal title | Journal of Electronic Packaging | |
| identifier doi | 10.1115/1.4024113 | |
| journal fristpage | 31007 | |
| journal lastpage | 31007 | |
| identifier eissn | 1043-7398 | |
| tree | Journal of Electronic Packaging:;2013:;volume( 135 ):;issue: 003 | |
| contenttype | Fulltext |