YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Fuel Cell Science and Technology
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Fuel Cell Science and Technology
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    The Influence of Chitosan Membrane Properties for Direct Methanol Fuel Cell Applications

    Source: Journal of Fuel Cell Science and Technology:;2012:;volume( 009 ):;issue: 001::page 11003
    Author:
    Peter O. Osifo
    ,
    Aluwani Masala
    DOI: 10.1115/1.4005382
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: The chitosan membranes with different degrees of deacetylation (dda), prepared from Cape rock lobster collected from the surroundings of Cape Town, South Africa were characterized for suitability in methanol fuel cell applications. A comparison of chitosan membranes characteristics and that of conventional Nafion 117 membranes were made. Following this, the chitosan membranes were chemically modified with sulfuric acid to improve its proton conductivity and mechanical properties. A mass balance on proton transfer across the membrane resulted in a second order differential equation. Experimental data fitted into the equation gives a linear curve that was used to determine the membrane resistance. It was found that the dda of the chitosan membranes affected the water uptake, thereby affecting the proton flow. At a temperature of 20°C, chitosan membranes with a difference of 10% dda have a difference of about 5% water content. Chitosan membranes with a lower dda were found to have higher water content resulting in lower membrane resistances to proton flow. The water content of chitosan membranes was higher than Nafion membranes. The average resistance to proton flow for chitosan membrane was 53 min/cm and a Nafion membrane was 78 min/cm. Thermogravimetry analysis shows that chitosan membrane with higher dda is more thermally stable than chitosan with lower dda, Nafion membranes were more stable at higher temperature than chitosan membranes, Nafion membranes could decompose at temperature of 320 °C while chitosan membranes at 230 °C. Methanol permeability through chitosan membrane of higher dda was more than with one lower dda, however, the permeability through chitosan was three times lower when compares to Nafion membranes under the same temperature and pressure conditions. The performance of chitosan membranes and Nafion 117 membranes measured from a single cell DMFC with Pt-Ru/C anode catalysts and Pt/C cathode catalysts showed that Nafion membranes have a better performance. This was because the current and peak power densities determined for Nafion membranes were 0.56 A/cm2 and 0.075 W/cm2 , respectively, and for Chit-I, were 0.22 A/cm2 and 0.0274 W/cm2 , respectively, and for Chit-II membrane, were 0.26 A/cm2 and 0.0424 W/cm2 , respectively.
    keyword(s): Membranes , Water AND Methanol ,
    • Download: (1.734Mb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      The Influence of Chitosan Membrane Properties for Direct Methanol Fuel Cell Applications

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/149268
    Collections
    • Journal of Fuel Cell Science and Technology

    Show full item record

    contributor authorPeter O. Osifo
    contributor authorAluwani Masala
    date accessioned2017-05-09T00:51:46Z
    date available2017-05-09T00:51:46Z
    date copyrightFebruary, 2012
    date issued2012
    identifier issn2381-6872
    identifier otherJFCSAU-28952#011003_1.pdf
    identifier urihttp://yetl.yabesh.ir/yetl/handle/yetl/149268
    description abstractThe chitosan membranes with different degrees of deacetylation (dda), prepared from Cape rock lobster collected from the surroundings of Cape Town, South Africa were characterized for suitability in methanol fuel cell applications. A comparison of chitosan membranes characteristics and that of conventional Nafion 117 membranes were made. Following this, the chitosan membranes were chemically modified with sulfuric acid to improve its proton conductivity and mechanical properties. A mass balance on proton transfer across the membrane resulted in a second order differential equation. Experimental data fitted into the equation gives a linear curve that was used to determine the membrane resistance. It was found that the dda of the chitosan membranes affected the water uptake, thereby affecting the proton flow. At a temperature of 20°C, chitosan membranes with a difference of 10% dda have a difference of about 5% water content. Chitosan membranes with a lower dda were found to have higher water content resulting in lower membrane resistances to proton flow. The water content of chitosan membranes was higher than Nafion membranes. The average resistance to proton flow for chitosan membrane was 53 min/cm and a Nafion membrane was 78 min/cm. Thermogravimetry analysis shows that chitosan membrane with higher dda is more thermally stable than chitosan with lower dda, Nafion membranes were more stable at higher temperature than chitosan membranes, Nafion membranes could decompose at temperature of 320 °C while chitosan membranes at 230 °C. Methanol permeability through chitosan membrane of higher dda was more than with one lower dda, however, the permeability through chitosan was three times lower when compares to Nafion membranes under the same temperature and pressure conditions. The performance of chitosan membranes and Nafion 117 membranes measured from a single cell DMFC with Pt-Ru/C anode catalysts and Pt/C cathode catalysts showed that Nafion membranes have a better performance. This was because the current and peak power densities determined for Nafion membranes were 0.56 A/cm2 and 0.075 W/cm2 , respectively, and for Chit-I, were 0.22 A/cm2 and 0.0274 W/cm2 , respectively, and for Chit-II membrane, were 0.26 A/cm2 and 0.0424 W/cm2 , respectively.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleThe Influence of Chitosan Membrane Properties for Direct Methanol Fuel Cell Applications
    typeJournal Paper
    journal volume9
    journal issue1
    journal titleJournal of Fuel Cell Science and Technology
    identifier doi10.1115/1.4005382
    journal fristpage11003
    identifier eissn2381-6910
    keywordsMembranes
    keywordsWater AND Methanol
    treeJournal of Fuel Cell Science and Technology:;2012:;volume( 009 ):;issue: 001
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian