YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Fuel Cell Science and Technology
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Fuel Cell Science and Technology
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    Electrical Performance of PEM Fuel Cells With Different Gas Diffusion Layers

    Source: Journal of Fuel Cell Science and Technology:;2011:;volume( 008 ):;issue: 004::page 41005
    Author:
    P. Gallo Stampino
    ,
    L. Omati
    ,
    G. Dotelli
    DOI: 10.1115/1.4003630
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: The microporous layer (MPL) is a key component of polymer electrolyte membrane fuel cells (PEM-FCs), and it is in charge of the gas and water management at the electrode-gas diffusion layer (GDL) interfaces. A MPL was prepared and coated onto two different commercial GDLs: a carbon paper (woven-non-woven (WNW)) and a carbon cloth (CC). Electrical performances of the so-obtained gas diffusion media (GDM), i.e., GDL coated with the MPL, were investigated in single cell testing (steady-state polarization curves) using a Nafion® catalyst coated membrane with a platinum loading of 0.5 mg/cm2 both for the anode and the cathode. Moreover, in order to better understand the polarization phenomena during the running of the FC, impedance spectroscopy was carried out in galvanostatic mode at different current densities. In particular, the effect of the air relative humidity (RH 100%, 80%, and 60%) was investigated, while the hydrogen was fed always fully humidified (100%). The WNW substrate has demonstrated to be superior to CC in a vast range of current densities (from open circuit voltage to 0.8 A/cm2). However, at high current density, the WNW GDM has some problems in water management.
    keyword(s): Flow (Dynamics) , Polarization (Electricity) , Membranes , Proton exchange membrane fuel cells , Gas diffusion layers , Carbon , Current density , Catalysts , Diffusion (Physics) , Pressure , Electric potential , Water resource management , Anodes , Hydrogen , Impedance spectroscopy , Textiles , Spectra (Spectroscopy) , Impedance (Electricity) , Water , Steady state , Platinum , Circuits , Electrical resistance AND Fuel cells ,
    • Download: (609.8Kb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      Electrical Performance of PEM Fuel Cells With Different Gas Diffusion Layers

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/146460
    Collections
    • Journal of Fuel Cell Science and Technology

    Show full item record

    contributor authorP. Gallo Stampino
    contributor authorL. Omati
    contributor authorG. Dotelli
    date accessioned2017-05-09T00:44:37Z
    date available2017-05-09T00:44:37Z
    date copyrightAugust, 2011
    date issued2011
    identifier issn2381-6872
    identifier otherJFCSAU-28949#041005_1.pdf
    identifier urihttp://yetl.yabesh.ir/yetl/handle/yetl/146460
    description abstractThe microporous layer (MPL) is a key component of polymer electrolyte membrane fuel cells (PEM-FCs), and it is in charge of the gas and water management at the electrode-gas diffusion layer (GDL) interfaces. A MPL was prepared and coated onto two different commercial GDLs: a carbon paper (woven-non-woven (WNW)) and a carbon cloth (CC). Electrical performances of the so-obtained gas diffusion media (GDM), i.e., GDL coated with the MPL, were investigated in single cell testing (steady-state polarization curves) using a Nafion® catalyst coated membrane with a platinum loading of 0.5 mg/cm2 both for the anode and the cathode. Moreover, in order to better understand the polarization phenomena during the running of the FC, impedance spectroscopy was carried out in galvanostatic mode at different current densities. In particular, the effect of the air relative humidity (RH 100%, 80%, and 60%) was investigated, while the hydrogen was fed always fully humidified (100%). The WNW substrate has demonstrated to be superior to CC in a vast range of current densities (from open circuit voltage to 0.8 A/cm2). However, at high current density, the WNW GDM has some problems in water management.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleElectrical Performance of PEM Fuel Cells With Different Gas Diffusion Layers
    typeJournal Paper
    journal volume8
    journal issue4
    journal titleJournal of Fuel Cell Science and Technology
    identifier doi10.1115/1.4003630
    journal fristpage41005
    identifier eissn2381-6910
    keywordsFlow (Dynamics)
    keywordsPolarization (Electricity)
    keywordsMembranes
    keywordsProton exchange membrane fuel cells
    keywordsGas diffusion layers
    keywordsCarbon
    keywordsCurrent density
    keywordsCatalysts
    keywordsDiffusion (Physics)
    keywordsPressure
    keywordsElectric potential
    keywordsWater resource management
    keywordsAnodes
    keywordsHydrogen
    keywordsImpedance spectroscopy
    keywordsTextiles
    keywordsSpectra (Spectroscopy)
    keywordsImpedance (Electricity)
    keywordsWater
    keywordsSteady state
    keywordsPlatinum
    keywordsCircuits
    keywordsElectrical resistance AND Fuel cells
    treeJournal of Fuel Cell Science and Technology:;2011:;volume( 008 ):;issue: 004
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian