YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    Influence of Intermetallic Characteristics on the Solder Joint Strength of Halogen-Free Printed Circuit Board Assembly

    Source: Journal of Electronic Packaging:;2011:;volume( 133 ):;issue: 002::page 21004
    Author:
    Hung-Jen Chang
    ,
    Tao-Chih Chang
    ,
    Min-Hsiung Hon
    ,
    Chi-Shiung Hsi
    ,
    Chau-Jie Zhan
    ,
    Jung-Hua Chou
    DOI: 10.1115/1.4003989
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: Five halogen-free (HF) dummy plastic ball grid array (PBGA) components with daisy-chains and Sn4.0Ag0.5Cu (SAC405) Pb-free solder balls were assembled on a HF high density interconnection (HDI) printed circuit board (PCB) using Sn1.0Ag0.5Cu (SAC105) and Sn3.0Ag0.5Cu (SAC305) Pb-free solder pastes, respectively. The above compositions were in weight percent. The assemblies were then experienced to moisture sensitive level testing with three times reflow at a peak temperature of 260 °C; no delamination was found present in both the component and PCB laminates. The microstructure showed that the utilization of SAC105 solder paste was beneficial in refining the Ag3Sn intermetallic compound (IMC) within the solder joint and the intermetallic layers formed at various interfaces with different Ni contents and thicknesses due to different metal finishes. The IMC spalling was found at the BGA-side interface within the solder joints formed with SAC105 solder paste but not discovered within the ones made of SAC305 solder paste. The pull strength of the solder joint formed with SAC305 solder paste was always higher than that made from SAC105 no matter on Cu or electroless Ni. Moreover, the fracture was found at the interface between the Cu foil and epoxy in the halogen-free test device. Numerical analysis showed that the thickness of IMC layer dominated the pull strength of the solder joint because the Z-axial normal stress applied to the solder joints formed with Cu and electroless Ni were 752.0 and 816.6 MPa, respectively, and a thicker IMC layer was beneficial to provide a higher pull strength of solder joint.
    keyword(s): Intermetallic compounds , Alloys , Solders , Lead-free solders , Solder joints , Thickness , Printed circuit board assemblies , Stress , Ball-Grid-Array packaging , Epoxy adhesives , Fracture (Process) AND Failure ,
    • Download: (2.593Mb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      Influence of Intermetallic Characteristics on the Solder Joint Strength of Halogen-Free Printed Circuit Board Assembly

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/145809
    Collections
    • Journal of Electronic Packaging

    Show full item record

    contributor authorHung-Jen Chang
    contributor authorTao-Chih Chang
    contributor authorMin-Hsiung Hon
    contributor authorChi-Shiung Hsi
    contributor authorChau-Jie Zhan
    contributor authorJung-Hua Chou
    date accessioned2017-05-09T00:43:12Z
    date available2017-05-09T00:43:12Z
    date copyrightJune, 2011
    date issued2011
    identifier issn1528-9044
    identifier otherJEPAE4-26313#021004_1.pdf
    identifier urihttp://yetl.yabesh.ir/yetl/handle/yetl/145809
    description abstractFive halogen-free (HF) dummy plastic ball grid array (PBGA) components with daisy-chains and Sn4.0Ag0.5Cu (SAC405) Pb-free solder balls were assembled on a HF high density interconnection (HDI) printed circuit board (PCB) using Sn1.0Ag0.5Cu (SAC105) and Sn3.0Ag0.5Cu (SAC305) Pb-free solder pastes, respectively. The above compositions were in weight percent. The assemblies were then experienced to moisture sensitive level testing with three times reflow at a peak temperature of 260 °C; no delamination was found present in both the component and PCB laminates. The microstructure showed that the utilization of SAC105 solder paste was beneficial in refining the Ag3Sn intermetallic compound (IMC) within the solder joint and the intermetallic layers formed at various interfaces with different Ni contents and thicknesses due to different metal finishes. The IMC spalling was found at the BGA-side interface within the solder joints formed with SAC105 solder paste but not discovered within the ones made of SAC305 solder paste. The pull strength of the solder joint formed with SAC305 solder paste was always higher than that made from SAC105 no matter on Cu or electroless Ni. Moreover, the fracture was found at the interface between the Cu foil and epoxy in the halogen-free test device. Numerical analysis showed that the thickness of IMC layer dominated the pull strength of the solder joint because the Z-axial normal stress applied to the solder joints formed with Cu and electroless Ni were 752.0 and 816.6 MPa, respectively, and a thicker IMC layer was beneficial to provide a higher pull strength of solder joint.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleInfluence of Intermetallic Characteristics on the Solder Joint Strength of Halogen-Free Printed Circuit Board Assembly
    typeJournal Paper
    journal volume133
    journal issue2
    journal titleJournal of Electronic Packaging
    identifier doi10.1115/1.4003989
    journal fristpage21004
    identifier eissn1043-7398
    keywordsIntermetallic compounds
    keywordsAlloys
    keywordsSolders
    keywordsLead-free solders
    keywordsSolder joints
    keywordsThickness
    keywordsPrinted circuit board assemblies
    keywordsStress
    keywordsBall-Grid-Array packaging
    keywordsEpoxy adhesives
    keywordsFracture (Process) AND Failure
    treeJournal of Electronic Packaging:;2011:;volume( 133 ):;issue: 002
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian