YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    Joint Level Test Methods for Solder Pad Cratering Investigations

    Source: Journal of Electronic Packaging:;2011:;volume( 133 ):;issue: 003::page 31007
    Author:
    Brian D. Roggeman
    ,
    Venkatesh Raghavan
    ,
    Peter Borgesen
    DOI: 10.1115/1.4004182
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: The introduction of less compliant lead free solders together with weaker and more brittle laminate materials has led to major concerns with respect to the resistance of the latter to pad cratering. For purposes of laminate selection as well as for the quantification of acceptable handling and use conditions, there is a general interest in the testing for cratering at the joint level, rather than by testing entire assemblies. Joint level testing is cheaper, faster, and offers more quantitative results. Joint level testing also allows the elimination of confounding factors such as PCB and component stiffness. Developing test procedures and testing, it is important to distinguish between wear out under repeated loads and the failure due to a single overstress. Correlations between these two damage scenarios are largely fortuitous. Focusing on strength testing we have compared alternative methods and identified the most relevant approach. Occasions may arise where shear testing is the most appropriate, but most pad cratering scenarios are best represented by so-called Hot Bump Pull at an angle of about 30° to the pad normal. Replacing the solder balls by paste deposits or pulling in a direction normal to the pad may lead to a different ranking of materials and otherwise obscure systematic trends. We also recommend taking loading rate and temperature effects into account.
    keyword(s): Solders , Laminates , Stress , Shear (Mechanics) , Testing , Failure , Resins AND Temperature ,
    • Download: (2.205Mb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      Joint Level Test Methods for Solder Pad Cratering Investigations

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/145787
    Collections
    • Journal of Electronic Packaging

    Show full item record

    contributor authorBrian D. Roggeman
    contributor authorVenkatesh Raghavan
    contributor authorPeter Borgesen
    date accessioned2017-05-09T00:43:09Z
    date available2017-05-09T00:43:09Z
    date copyrightSeptember, 2011
    date issued2011
    identifier issn1528-9044
    identifier otherJEPAE4-26316#031007_1.pdf
    identifier urihttp://yetl.yabesh.ir/yetl/handle/yetl/145787
    description abstractThe introduction of less compliant lead free solders together with weaker and more brittle laminate materials has led to major concerns with respect to the resistance of the latter to pad cratering. For purposes of laminate selection as well as for the quantification of acceptable handling and use conditions, there is a general interest in the testing for cratering at the joint level, rather than by testing entire assemblies. Joint level testing is cheaper, faster, and offers more quantitative results. Joint level testing also allows the elimination of confounding factors such as PCB and component stiffness. Developing test procedures and testing, it is important to distinguish between wear out under repeated loads and the failure due to a single overstress. Correlations between these two damage scenarios are largely fortuitous. Focusing on strength testing we have compared alternative methods and identified the most relevant approach. Occasions may arise where shear testing is the most appropriate, but most pad cratering scenarios are best represented by so-called Hot Bump Pull at an angle of about 30° to the pad normal. Replacing the solder balls by paste deposits or pulling in a direction normal to the pad may lead to a different ranking of materials and otherwise obscure systematic trends. We also recommend taking loading rate and temperature effects into account.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleJoint Level Test Methods for Solder Pad Cratering Investigations
    typeJournal Paper
    journal volume133
    journal issue3
    journal titleJournal of Electronic Packaging
    identifier doi10.1115/1.4004182
    journal fristpage31007
    identifier eissn1043-7398
    keywordsSolders
    keywordsLaminates
    keywordsStress
    keywordsShear (Mechanics)
    keywordsTesting
    keywordsFailure
    keywordsResins AND Temperature
    treeJournal of Electronic Packaging:;2011:;volume( 133 ):;issue: 003
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian