YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Electronic Packaging
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    Solid-State Microrefrigeration in Conjunction With Liquid Cooling

    Source: Journal of Electronic Packaging:;2010:;volume( 132 ):;issue: 003::page 31002
    Author:
    Younes Ezzahri
    ,
    Ali Shakouri
    DOI: 10.1115/1.4001853
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: Thermal design requirements are mostly driven by the peak temperatures. Reducing or eliminating hot spots could alleviate the design requirement for the whole package. Combination of solid-state and liquid cooling will allow removal of both hot spots and background heating. In this paper, we analyze the performance of thin film Bi2Te3 microcooler and the 3D SiGe-based microrefrigerator, and optimize the maximum cooling and cooling power density in the presence of a liquid flow. Liquid flow and heat transfer coefficient will change the background temperature of the chip but they also affect the performance of the solid-state coolers used to remove hot spots. Both Peltier cooling at interfaces and Joule heating inside the device could be affected by the fluid flow. We analyze conventional Peltier coolers as well as 3D coolers. We study the impact of various parameters such as thermoelectric leg thickness, thermal interface resistances, and geometry factor on the overall system performance. We find that the cooling of a conventional Peltier cooler is significantly reduced in the presence of fluid flow. On the other hand, 3D SiGe cooler can be effective to remove high power density hot spots up to 500 W/cm2. 3D microrefrigerators can have a significant impact if the thermoelectric figure-of-merit, ZT, could reach 0.5 for a material grown on silicon substrate. It is interesting to note that there is an optimum microrefrigerator active region thickness that gives the maximum localized cooling. For liquid heat transfer coefficient between 5000 and 20,000 W m−2 K−1, the optimum is found to be between 10 μm and 20 μm.
    keyword(s): Thin films , Temperature , Cooling , Thickness AND Heat transfer coefficients ,
    • Download: (1.057Mb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      Solid-State Microrefrigeration in Conjunction With Liquid Cooling

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/142942
    Collections
    • Journal of Electronic Packaging

    Show full item record

    contributor authorYounes Ezzahri
    contributor authorAli Shakouri
    date accessioned2017-05-09T00:37:12Z
    date available2017-05-09T00:37:12Z
    date copyrightSeptember, 2010
    date issued2010
    identifier issn1528-9044
    identifier otherJEPAE4-26306#031002_1.pdf
    identifier urihttp://yetl.yabesh.ir/yetl/handle/yetl/142942
    description abstractThermal design requirements are mostly driven by the peak temperatures. Reducing or eliminating hot spots could alleviate the design requirement for the whole package. Combination of solid-state and liquid cooling will allow removal of both hot spots and background heating. In this paper, we analyze the performance of thin film Bi2Te3 microcooler and the 3D SiGe-based microrefrigerator, and optimize the maximum cooling and cooling power density in the presence of a liquid flow. Liquid flow and heat transfer coefficient will change the background temperature of the chip but they also affect the performance of the solid-state coolers used to remove hot spots. Both Peltier cooling at interfaces and Joule heating inside the device could be affected by the fluid flow. We analyze conventional Peltier coolers as well as 3D coolers. We study the impact of various parameters such as thermoelectric leg thickness, thermal interface resistances, and geometry factor on the overall system performance. We find that the cooling of a conventional Peltier cooler is significantly reduced in the presence of fluid flow. On the other hand, 3D SiGe cooler can be effective to remove high power density hot spots up to 500 W/cm2. 3D microrefrigerators can have a significant impact if the thermoelectric figure-of-merit, ZT, could reach 0.5 for a material grown on silicon substrate. It is interesting to note that there is an optimum microrefrigerator active region thickness that gives the maximum localized cooling. For liquid heat transfer coefficient between 5000 and 20,000 W m−2 K−1, the optimum is found to be between 10 μm and 20 μm.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleSolid-State Microrefrigeration in Conjunction With Liquid Cooling
    typeJournal Paper
    journal volume132
    journal issue3
    journal titleJournal of Electronic Packaging
    identifier doi10.1115/1.4001853
    journal fristpage31002
    identifier eissn1043-7398
    keywordsThin films
    keywordsTemperature
    keywordsCooling
    keywordsThickness AND Heat transfer coefficients
    treeJournal of Electronic Packaging:;2010:;volume( 132 ):;issue: 003
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian