Experimental Investigation on the Process-Induced Damage of a Direct Methanol Fuel Cell Assembled by the Printed Circuit Board TechniqueSource: Journal of Fuel Cell Science and Technology:;2009:;volume( 006 ):;issue: 001::page 11016DOI: 10.1115/1.2971130Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: The printed circuit board (PCB)-based direct methanol fuel cell (DMFC) package is a novel manufacturing and assembly process, which is full potential in mass production, and very limited literatures make study on the effects of the related process parameters. The hot press is a necessary and key process to make the PCB package, i.e., the key component of a DMFC, membrane electrode assemblies (MEA), needs to sustain a severe test. In order to minimize the process-induced damage of the MEAs, it is important to make a good control on the process parameters. Therefore, the objective of this paper is to present a methodology to explore a good combination of hot-press parameters. The considered parameters include the compression ratio of the MEA, heating time, heating temperature, and hot pressing pressure acting on the MEA. During the experimental investigation, a series of experiments was made first to discuss the effect of the individual parameter of the hot-press process on the MEA performance, wherein a reasonable range of each process parameter condition was able to be well defined. Moreover, the Taguchi experimental method was adopted to explore the parameter effects on the DMFC performance during the digital packaging process and to determine the best combination of parameter conditions. At the end, a MEA was made a hot press under the best parameter combination, which could verify the result obtained from Taguchi’s experiments. The result is able to be an important reference for the future manufacturing design guideline of PCB-based DMFC package.
keyword(s): Pressure , Temperature , Manufacturing , Compression , Direct methanol fuel cells , Hot pressing , Heating , Printed circuit boards AND Presses ,
|
Collections
Show full item record
| contributor author | Yean-Der Kuan | |
| contributor author | Chia-Hao Chang | |
| date accessioned | 2017-05-09T00:33:30Z | |
| date available | 2017-05-09T00:33:30Z | |
| date copyright | February, 2009 | |
| date issued | 2009 | |
| identifier issn | 2381-6872 | |
| identifier other | JFCSAU-28936#011016_1.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/140898 | |
| description abstract | The printed circuit board (PCB)-based direct methanol fuel cell (DMFC) package is a novel manufacturing and assembly process, which is full potential in mass production, and very limited literatures make study on the effects of the related process parameters. The hot press is a necessary and key process to make the PCB package, i.e., the key component of a DMFC, membrane electrode assemblies (MEA), needs to sustain a severe test. In order to minimize the process-induced damage of the MEAs, it is important to make a good control on the process parameters. Therefore, the objective of this paper is to present a methodology to explore a good combination of hot-press parameters. The considered parameters include the compression ratio of the MEA, heating time, heating temperature, and hot pressing pressure acting on the MEA. During the experimental investigation, a series of experiments was made first to discuss the effect of the individual parameter of the hot-press process on the MEA performance, wherein a reasonable range of each process parameter condition was able to be well defined. Moreover, the Taguchi experimental method was adopted to explore the parameter effects on the DMFC performance during the digital packaging process and to determine the best combination of parameter conditions. At the end, a MEA was made a hot press under the best parameter combination, which could verify the result obtained from Taguchi’s experiments. The result is able to be an important reference for the future manufacturing design guideline of PCB-based DMFC package. | |
| publisher | The American Society of Mechanical Engineers (ASME) | |
| title | Experimental Investigation on the Process-Induced Damage of a Direct Methanol Fuel Cell Assembled by the Printed Circuit Board Technique | |
| type | Journal Paper | |
| journal volume | 6 | |
| journal issue | 1 | |
| journal title | Journal of Fuel Cell Science and Technology | |
| identifier doi | 10.1115/1.2971130 | |
| journal fristpage | 11016 | |
| identifier eissn | 2381-6910 | |
| keywords | Pressure | |
| keywords | Temperature | |
| keywords | Manufacturing | |
| keywords | Compression | |
| keywords | Direct methanol fuel cells | |
| keywords | Hot pressing | |
| keywords | Heating | |
| keywords | Printed circuit boards AND Presses | |
| tree | Journal of Fuel Cell Science and Technology:;2009:;volume( 006 ):;issue: 001 | |
| contenttype | Fulltext |