YaBeSH Engineering and Technology Library

    • Journals
    • PaperQuest
    • YSE Standards
    • YaBeSH
    • Login
    View Item 
    •   YE&T Library
    • ASME
    • Journal of Fuel Cell Science and Technology
    • View Item
    •   YE&T Library
    • ASME
    • Journal of Fuel Cell Science and Technology
    • View Item
    • All Fields
    • Source Title
    • Year
    • Publisher
    • Title
    • Subject
    • Author
    • DOI
    • ISBN
    Advanced Search
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Archive

    Discussion and Analysis of Flue Gas Utilization in a Phosphoric Acid Fuel Cell Engine During Idle Operation

    Source: Journal of Fuel Cell Science and Technology:;2006:;volume( 003 ):;issue: 001::page 26
    Author:
    Daniel A. Betts
    ,
    Vernon P. Roan
    ,
    James H. Fletcher
    DOI: 10.1115/1.2133803
    Publisher: The American Society of Mechanical Engineers (ASME)
    Abstract: Fuel cell technology has in recent years won the favor of all major car manufacturers as a likely future replacement of the internal combustion engine. This has been driven by the potential for high efficiency and low emissions. Still, fuel cell engines must overcome major hurdles before being introduced into the market. One such hurdle is systems integration; in particular, with fuel cell engines that do not use hydrogen as their primary fuel. In these engines, fuels, such as methanol, are employed instead of hydrogen because of their high-energy density and ease of storage. However, these benefits are counterbalanced by the need to reform these fuels on-board the fuel cell vehicle, thus substantially increasing the complexity of the fuel cell engine. Through the course of operating a 30ft methanol-fueled phosphoric acid fuel cell bus, repeated overheating of the steam-reformer catalyst bed at low engine power outputs was noted. For the purpose of better understanding these overheating events, relevant data was obtained from the bus. Bus operation at low-power outputs was found to have low hydrogen consumption (∼40% to ∼60% of the stack’s incoming hydrogen) due to low electrical demands and reformate flow rate constraints. In the bus, the anode flue gas is burned in the reformer burner, which provides the heat required for the endothermic methanol steam reforming reaction (see Fig. 1 later). At low engine power, the flue gas is the reformer burner’s only fuel, but the energy carried by the flue gas is much greater than the energy required for the reforming reaction and consequently causes reformer overheating at low power. This case serves as an example of how appropriate fuel cell system integration is crucial in order to harness fuel cell benefits. To study such system integration problems, a steady-state model of the fuel cell bus engine was developed. Using this model the bus reformer overheating problem was understood and several possible improvements for utilization of the flue gas were conceited.
    keyword(s): Fuels , Engines , Fuel cells , Flue gases , Hydrogen , Phosphoric acid fuel cells , Flow (Dynamics) , Heat , Methanol , Catalysts , Anodes , Emissions AND Steam reforming ,
    • Download: (741.9Kb)
    • Show Full MetaData Hide Full MetaData
    • Get RIS
    • Item Order
    • Go To Publisher
    • Statistics

      Discussion and Analysis of Flue Gas Utilization in a Phosphoric Acid Fuel Cell Engine During Idle Operation

    URI
    https://yetl.yabesh.ir/yetl1/handle/yetl/134087
    Collections
    • Journal of Fuel Cell Science and Technology

    Show full item record

    contributor authorDaniel A. Betts
    contributor authorVernon P. Roan
    contributor authorJames H. Fletcher
    date accessioned2017-05-09T00:20:37Z
    date available2017-05-09T00:20:37Z
    date copyrightFebruary, 2006
    date issued2006
    identifier issn2381-6872
    identifier otherJFCSAU-28924#26_1.pdf
    identifier urihttp://yetl.yabesh.ir/yetl/handle/yetl/134087
    description abstractFuel cell technology has in recent years won the favor of all major car manufacturers as a likely future replacement of the internal combustion engine. This has been driven by the potential for high efficiency and low emissions. Still, fuel cell engines must overcome major hurdles before being introduced into the market. One such hurdle is systems integration; in particular, with fuel cell engines that do not use hydrogen as their primary fuel. In these engines, fuels, such as methanol, are employed instead of hydrogen because of their high-energy density and ease of storage. However, these benefits are counterbalanced by the need to reform these fuels on-board the fuel cell vehicle, thus substantially increasing the complexity of the fuel cell engine. Through the course of operating a 30ft methanol-fueled phosphoric acid fuel cell bus, repeated overheating of the steam-reformer catalyst bed at low engine power outputs was noted. For the purpose of better understanding these overheating events, relevant data was obtained from the bus. Bus operation at low-power outputs was found to have low hydrogen consumption (∼40% to ∼60% of the stack’s incoming hydrogen) due to low electrical demands and reformate flow rate constraints. In the bus, the anode flue gas is burned in the reformer burner, which provides the heat required for the endothermic methanol steam reforming reaction (see Fig. 1 later). At low engine power, the flue gas is the reformer burner’s only fuel, but the energy carried by the flue gas is much greater than the energy required for the reforming reaction and consequently causes reformer overheating at low power. This case serves as an example of how appropriate fuel cell system integration is crucial in order to harness fuel cell benefits. To study such system integration problems, a steady-state model of the fuel cell bus engine was developed. Using this model the bus reformer overheating problem was understood and several possible improvements for utilization of the flue gas were conceited.
    publisherThe American Society of Mechanical Engineers (ASME)
    titleDiscussion and Analysis of Flue Gas Utilization in a Phosphoric Acid Fuel Cell Engine During Idle Operation
    typeJournal Paper
    journal volume3
    journal issue1
    journal titleJournal of Fuel Cell Science and Technology
    identifier doi10.1115/1.2133803
    journal fristpage26
    journal lastpage32
    identifier eissn2381-6910
    keywordsFuels
    keywordsEngines
    keywordsFuel cells
    keywordsFlue gases
    keywordsHydrogen
    keywordsPhosphoric acid fuel cells
    keywordsFlow (Dynamics)
    keywordsHeat
    keywordsMethanol
    keywordsCatalysts
    keywordsAnodes
    keywordsEmissions AND Steam reforming
    treeJournal of Fuel Cell Science and Technology:;2006:;volume( 003 ):;issue: 001
    contenttypeFulltext
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian
     
    DSpace software copyright © 2002-2015  DuraSpace
    نرم افزار کتابخانه دیجیتال "دی اسپیس" فارسی شده توسط یابش برای کتابخانه های ایرانی | تماس با یابش
    yabeshDSpacePersian