Design and Control of a Force-Reflecting Haptic Interface for Teleoperational GraspingSource: Journal of Mechanical Design:;2002:;volume( 124 ):;issue: 002::page 277DOI: 10.1115/1.1470493Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: In this paper the design of a multi-finger force-reflecting haptic interface device for teleoperational grasping is introduced. The haptic interface or “master” controller device is worn on the human operator’s hand and measured human finger positions are used to control the finger positions of a remote grasping manipulator or “slave” device. The slave may be a physical robotic grasping manipulator, or a computer generated representation of a human hand such as used in virtual reality applications. The forces measured by the robotic slave, or calculated for the virtual slave, are presented to the operator’s fingertips through the master providing a means for deeper human sensation of presence and better control of grasping tasks in the slave environments. Design parameters and performance measures for haptic interfaces for teleoperation are discussed. One key performance issue involving the high-speed display of forces during initial contact, especially when interacting with rigid surfaces, is addressed by the present design, reducing slave controller computation requirements and overcoming actuator response time constraints. The design presented utilizes a planar four-bar linkage for each finger, to represent each finger bend motion as a single degree of freedom, and to provide a finger bend resistance force that is substantially perpendicular to the distal finger pad throughout the full 180 degrees of finger bend motion represented. The finger linkage design, in combination with a remote position measurement and force display assembly, provides a very lightweight and low inertia system with a large workspace. The concept of a replicated finger is introduced which, in combination with a decoupled actuator and feed forward control, provides improved performance in transparent free motion, and rapid, stable touch sensation of initial contact with rigid surfaces. A distributed computation architecture with a PC based haptic interface controller and associated control algorithms are also discussed.
keyword(s): Force , Motion , Design , Grasping , Haptic interfaces , Control algorithms , Haptics AND Degrees of freedom ,
|
Collections
Show full item record
| contributor author | Scott L. Springer | |
| contributor author | Nicola J. Ferrier | |
| date accessioned | 2017-05-09T00:08:17Z | |
| date available | 2017-05-09T00:08:17Z | |
| date copyright | June, 2002 | |
| date issued | 2002 | |
| identifier issn | 1050-0472 | |
| identifier other | JMDEDB-27720#277_1.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/127238 | |
| description abstract | In this paper the design of a multi-finger force-reflecting haptic interface device for teleoperational grasping is introduced. The haptic interface or “master” controller device is worn on the human operator’s hand and measured human finger positions are used to control the finger positions of a remote grasping manipulator or “slave” device. The slave may be a physical robotic grasping manipulator, or a computer generated representation of a human hand such as used in virtual reality applications. The forces measured by the robotic slave, or calculated for the virtual slave, are presented to the operator’s fingertips through the master providing a means for deeper human sensation of presence and better control of grasping tasks in the slave environments. Design parameters and performance measures for haptic interfaces for teleoperation are discussed. One key performance issue involving the high-speed display of forces during initial contact, especially when interacting with rigid surfaces, is addressed by the present design, reducing slave controller computation requirements and overcoming actuator response time constraints. The design presented utilizes a planar four-bar linkage for each finger, to represent each finger bend motion as a single degree of freedom, and to provide a finger bend resistance force that is substantially perpendicular to the distal finger pad throughout the full 180 degrees of finger bend motion represented. The finger linkage design, in combination with a remote position measurement and force display assembly, provides a very lightweight and low inertia system with a large workspace. The concept of a replicated finger is introduced which, in combination with a decoupled actuator and feed forward control, provides improved performance in transparent free motion, and rapid, stable touch sensation of initial contact with rigid surfaces. A distributed computation architecture with a PC based haptic interface controller and associated control algorithms are also discussed. | |
| publisher | The American Society of Mechanical Engineers (ASME) | |
| title | Design and Control of a Force-Reflecting Haptic Interface for Teleoperational Grasping | |
| type | Journal Paper | |
| journal volume | 124 | |
| journal issue | 2 | |
| journal title | Journal of Mechanical Design | |
| identifier doi | 10.1115/1.1470493 | |
| journal fristpage | 277 | |
| journal lastpage | 283 | |
| identifier eissn | 1528-9001 | |
| keywords | Force | |
| keywords | Motion | |
| keywords | Design | |
| keywords | Grasping | |
| keywords | Haptic interfaces | |
| keywords | Control algorithms | |
| keywords | Haptics AND Degrees of freedom | |
| tree | Journal of Mechanical Design:;2002:;volume( 124 ):;issue: 002 | |
| contenttype | Fulltext |