Show simple item record

dc.contributor.authorJ. K. Hayes
dc.contributor.authorS. E. Moore
dc.date.accessioned2017-05-08T23:03:36Z
dc.date.available2017-05-08T23:03:36Z
dc.date.copyrightNovember, 1977
dc.date.issued1977
dc.identifier.issn0094-9930
dc.identifier.otherJPVTAS-28155#537_1.pdf
dc.identifier.urihttp://yetl.yabesh.ir/yetl/handle/yetl/90323
dc.description.abstractThis paper describes the experimental stress analysis of low cycle fatigue tests of four tees tested by Combustion Engineering, Inc. (C-E) under subcontract to Union Carbide Nuclear Division. These tests are part of the ORNL Design Criteria for Piping and Nozzles Program which is being conducted for the development of design criteria for nuclear power plant service piping components. The test assemblies were fabricated at C-E from commercially obtained ANSI B16.9 tees and matching diameter steel pipes welded to the tees, with suitable end closures and fixtures for applying the loads. The tees tested and discussed in this report are described in the following: Tee Number/Material/Nominal Size: T–11/carbon steel/24″ ×24″ ×24″ sch 160; T–12/carbon steel/24″ ×24″ ×10″ sch 40; T–13/carbon steel/24″ ×24″ ×10″ sch 160; T–16/stainless steel/24″ ×24″ ×24″ sch 10. Each tee test assembly was instrumented with approximately 240 rectangular strain gage rosettes for determining elastic stress distributions, and six linear variable displacement transducers for determining flexibility factors. Elastic-response tests were conducted for 12 loading conditions consisting of internal pressure, pure bending and torsional moments and direct force loads applied individually to the branch pipe extension and to one end of the run pipe. The other run pipe extension was fixed rigidly to the loading frame. Automatic data handling equipment and data reduction techniques were used to process the strain gage readings. For each loading condition, stress distributions were determined and the locations and magnitudes of the maximum stresses were identified. Test results are presented and compared with appropriate design formulas of the ASME Boiler and Pressure Vessel Code, Section III. After the elastic-response tests were completed, three of the tees were low-cycle fatigue tested by pressure cycling using transformer oil. The T-11 and T-13 tees were pressure cycled for 100 psig (790 kPa) to 7000 psig (48 360 kPa); whereas, the T-12 tee was pressure cycled from 0 psig (100 kPa) to 1800 psig (12 510 kPa). A low-cycle fatigue test was performed on the T-16 tee assembly by applying a bending moment to the branch pipe in the plane of the tee with the tee pressurized to a constant internal pressure of 300 psig (2170 kPa). All low-cycle fatigue tests were performed until a through-the-wall fatigue crack occurred as evidenced by a leak. Subparagraph NB-3653.6 of ASME Code, Section III, Division I, Nuclear Power Plant Components was used to calculate the fatigue design life and comparisons were made with the experimentally determined fatigue life.
dc.publisherThe American Society of Mechanical Engineers (ASME)
dc.titleExperimental Stress Analysis for Four 24-in. ANSI Standard B16.9 Tees
dc.typeJournal Paper
dc.journal.volume99
dc.journal.issue4
dc.journal.titleJournal of Pressure Vessel Technology
dc.identifier.doi10.1115/1.3454572
dc.journal.fristpage537
dc.journal.lastpage552
dc.identifier.eissn1528-8978
dc.keywordsStress analysis (Engineering)
dc.keywordsPipes
dc.keywordsPressure
dc.keywordsStress
dc.keywordsLow cycle fatigue
dc.keywordsCarbon steel
dc.keywordsDesign
dc.keywordsBifurcation
dc.keywordsManufacturing
dc.keywordsNuclear power stations
dc.keywordsStrain gages
dc.keywordsLeakage
dc.keywordsASME Standards
dc.keywordsStainless steel
dc.keywordsForce
dc.keywordsPlasticity
dc.keywordsSteel
dc.keywordsJigs and fixtures
dc.keywordsStructural frames
dc.keywordsCombustion engineering
dc.keywordsDisplacement
dc.keywordsFatigue cracks
dc.keywordsFatigue design
dc.keywordsFatigue life
dc.keywordsFormulas
dc.keywordsNozzles
dc.keywordsTransducers AND ASME Boiler and Pressure Vessel Code
dc.treeJournal of Pressure Vessel Technology:;1977:;volume( 099 ):;issue: 004
dc.contenttypeFulltext


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record