Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3121-3140 of 3257
-
Models for Fibrous Composites With Different Properties in Tension and Compression
(The American Society of Mechanical Engineers (ASME), 1977)It has been observed that certain filamentary composite materials exhibit a different Poisson compliance when loaded transversely to the fibers than when loaded longitudinally (parallel to the ... -
Review of the Mechanical Properties of Cast Steels With Emphasis on Fatigue Behavior and the Influence of Microdiscontinuities
(The American Society of Mechanical Engineers (ASME), 1977)Mechanical properties of cast steels are pronouncedly affected by the microdiscontinuities which they inherently contain. In particular, fatigue behavior of cast steels is altered by (1) the size, ... -
Representation of Elevated-Temperature Tensile Behavior of Type 304 Stainless Steel in a Sodium Environment
(The American Society of Mechanical Engineers (ASME), 1977)An analysis of tensile behavior of Type 304 stainless steel was conducted for specimens in the solution-annealed condition and after exposure to a sodium environment. The Voce equation was used ... -
Fatigue Damage Detection in 2024-T3 Aluminum, Titanium, and Low Carbon Steel by Optical Correlation
(The American Society of Mechanical Engineers (ASME), 1977)Optical correlation techniques were used to monitor fatigue damage in three metals of different strength and ductility, namely 2024-T3 aluminum alloy, commercial purity titanium, and low carbon ... -
Enhancement of Fatigue Crack Growth and Fracture Resistance in Ti-6Al-4V and Ti-6Al-6V-2Sn Through Microstructural Modification
(The American Society of Mechanical Engineers (ASME), 1977)Significant enhancement in fatigue crack propagation resistance and plane strain fracture toughness was obtained in commercial purity Ti-6Al-4V and Ti-6Al-6V-2Sn through microstructural modification. ... -
Further Dynamic Finite Element Analysis of the Tapered DCB Specimen
(The American Society of Mechanical Engineers (ASME), 1977)A dynamic finite element code was used to compute the dynamic stress intensity factors and crack arrest stress intensity factor which are related to the crack run-arrest response in a tapered ... -
The Effect of Plastic Strain Followed by Aging on the Elastic Limit of Quenched and Tempered and Austempered 4340 Steel
(The American Society of Mechanical Engineers (ASME), 1977) -
Fracture Mechanics Parameters for a 5083-0 Aluminum Alloy at Low Temperatures
(The American Society of Mechanical Engineers (ASME), 1977)The fatigue crack growth and fracture resistance of a 5083-0 aluminum alloy plate were investigated at four temperatures in the ambient-to-cryogenic range—295, 111, 76, and 4 K. J-integral test ... -
Applicability of Fracture Mechanics Parameters to Crack Propagation Under Creep Condition
(The American Society of Mechanical Engineers (ASME), 1977)A critical examination was made of the applicability of fracture mechanics parameters to crack propagation under creep condition with 304 stainless steels for a variety of specimen geometries ... -
Blunting of a Plane Strain Crack Tip Into a Shape With Vertices
(The American Society of Mechanical Engineers (ASME), 1977)When monotonically increasing tensile opening loads are applied to a cracked, plane strain, elastic-plastic body, the crack tip will blunt until fracture occurs. At least within the rigid-plastic ... -
Discussion: “A J-Integral Approach to Crack Resistance for Aluminum, Steel, and Titanium Alloys” (Wilhem, D. P., Ratwani, M. M., and Zielsdorff, G. F., 1977, ASME J. Eng. Mater. Technol., 99, pp. 97–104)
(The American Society of Mechanical Engineers (ASME), 1977) -
Development of Constitutive Relation for Plastic Deformation From a Dislocation Model
(The American Society of Mechanical Engineers (ASME), 1976)Further analysis of a model in which creep is attributed to the movement generation, immobilization, and recovery of dislocations has permitted the anelastic (recoverable) component of strain to ... -
Laws for Work-Hardening and Low-Temperature Creep
(The American Society of Mechanical Engineers (ASME), 1976)The true stress-strain curves of polycrystalline aluminum, copper, and stainless steel are shown to be adequately represented by an exponential approach to a saturation stress over a significant ... -
Interpretation of Irradiation Effects on the Fracture Toughness of a Pressure Vessel Steel in Terms of Crack Tip Stress Analysis
(The American Society of Mechanical Engineers (ASME), 1976)The model of Ritchie, Knott, and Rice [10], relating the critical tensile stress for initiation of unstable cleavage fracture of mild steel to the cryogenic temperature-dependence of plane strain ... -
Computer Simulation of Plastic Deformation Through Planar Glide in an Idealized Crystal
(The American Society of Mechanical Engineers (ASME), 1976)In this paper we report the behavior of the plastic deformation of an idealized crystal made by stacking parallel slip planes. Each slip plane is assumed to contain active sources of dislocations ... -
Failure Analysis of Cast Irons Under General Three-Dimensional Stress States
(The American Society of Mechanical Engineers (ASME), 1976)Observations of microscale behavior of cast irons indicate that considerable plastic flow occurs between microflaws prior to rupture. Therefore, the plastic limit load for small representative ... -
Moisture Diffusion in Fiber Reinforced Plastics
(The American Society of Mechanical Engineers (ASME), 1976)Fiber-reinforced epoxy laminates were exposed to several combinations of temperature and relative humidity. The purpose was to determine rates and extent of moisture absorption. Diffusion rates ... -
The Initiation and Propagation of Ductile Fracture in Low Strength Steels
(The American Society of Mechanical Engineers (ASME), 1976)The effects of work hardening rate and inclusion content on the initiation and propagation of ductile fracture in low strength steels have been investigated. A model has been proposed based ... -
Formation of Cavities From Nondeformable Second-Phase Particles in Low Temperature Ductile Fracture
(The American Society of Mechanical Engineers (ASME), 1976)Limiting solutions are discussed for elastic-plastic deformation around rigid particles of both equiaxed and greatly elongated shapes. It is shown that if the matrix can be characterized as a ... -
Constitutive Relationships for the Time-Dependent Deformation of Metals
(The American Society of Mechanical Engineers (ASME), 1976)The paper discusses the constitutive relations for the inelastic deformation of a polycrystalline metal at high temperature. Commencing from a description of a dislocation structure in terms of ...