Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2161-2180 of 3257
-
On Compression of Rubber Elastic Sphere Over a Large Range of Displacements—Part 1: Theoretical Study
(The American Society of Mechanical Engineers (ASME), 1991)This paper presents one general theory of large elastic deformations of a rubber sphere in simple compression, as the removal of restrictions of the constant Young modulus and small deformation ... -
A Rate-Dependent Inelastic Constitutive Model—Part I: Elastic-Plastic Flow
(The American Society of Mechanical Engineers (ASME), 1991)In this part a rate-dependent elastic-plastic constitutive model is presented which is an extension of our earlier rate-indpendent model. The effect of prior creep on the subsequent inelastic ... -
Analysis of Flow Patterns and Solidification Phenomena in the Die Casting Process
(The American Society of Mechanical Engineers (ASME), 1991)An analysis of the flow patterns and associated solidification phenomena during the die casting process is presented. In the filling stage of the die cavity, the flow patterns are predicted ... -
Acoustic Emission Monitoring of the Cutting Process—Negating the Influence of Varying Conditions
(The American Society of Mechanical Engineers (ASME), 1991)Earlier work has shown tool failure monitoring using frequency-based pattern recognition analysis of acoustic emission signals to be feasible while machining under fixed cutting conditions. However, ... -
Evaluation of the Vanishing Fiber Diameter Model for Composite Plasticity
(The American Society of Mechanical Engineers (ASME), 1991)The Vanishing Fiber Diameter (VFD) model for composite plasticity offers a computationally efficient approach to composite structural analysis and design problems. However this material model ... -
Modeling of Delayed Hydride Crack Initiation
(The American Society of Mechanical Engineers (ASME), 1991)This paper presents a solution to the one-dimensional time (transient condition) and temperature dependent diffusion problem adjacent to a crack-tip/flaw within the plastic zone region. The solution ... -
EDM Surface Characterization of a Ceramic Composite TiB2/SiC
(The American Society of Mechanical Engineers (ASME), 1991)Electrical Discharge Machined (EDM) hole surface characteristics of 20 percent Titanium diboride (TiB2 ) particulate and Silicon carbide (SiC) matrix composite material were investigated. The EDM ... -
Stress-Strain Equations for Some Near-Eutectic Tin-Lead Solders
(The American Society of Mechanical Engineers (ASME), 1991)This paper presents the evaluation of the stress-strain behavior, as a function of strain-rate, for three tin-lead solders at room temperature. This behavior is critically needed for reliability ... -
Nonlinear Response of Resin Matrix Laminates Using Endochronic Theory
(The American Society of Mechanical Engineers (ASME), 1991)The nonlinear response of laminated, resin matrix fibrous composites is modeled using orthotropic endochronic theory. The theory is formulated in terms of elastic constants and endochronic parameters ... -
Analysis of Shear Banding in Plane Strain Compression of a Bimetallic Thermally Softening Viscoplastic Body Containing an Elliptical Void
(The American Society of Mechanical Engineers (ASME), 1991)We study plane strain thermomechanical deformations of a prismatic viscoplastic body of square cross-section and deformed at a nominal strain-rate of 5000 s−1 . The body has two thin layers ... -
Elastic Buckling of Infinitely Long Specially Orthotropic Plates on Tensionless Foundations
(The American Society of Mechanical Engineers (ASME), 1991)The results of an analytical study on the elastic buckling of long narrow orthotropic plates resting on a tensionless foundation are reported. The motivation for the present study stems from ... -
A Yield Criterion of Porous Materials With Anisotropy Caused by Geometry or Distribution of Pores
(The American Society of Mechanical Engineers (ASME), 1991)Axisymmetric deformation of anisotropic porous materials caused by geometry of pores or by distribution of pores is analyzed. Two models of the materials are proposed: one consists of spherical ... -
Elastic Wave Propagation in Laminated Composite Plates
(The American Society of Mechanical Engineers (ASME), 1991)A stiffness method and an analytical method have been used to study the dispersion characteristics of guided waves in laminated composite plates. Both cross-ply and angle-ply plates have been ... -
Machining of Graphite/Epoxy Composite Materials With Polycrystalline Diamond (PCD) Tools
(The American Society of Mechanical Engineers (ASME), 1991)Machining of graphite/epoxy composite material is investigated by turning (cutoff) tests using different grades of polycrystalline diamond (PCD) inserts. The wear behavior of the PCD cutting edge ... -
An Application of Incremental Plasticity Theory to Fatigue Life Prediction of Steels
(The American Society of Mechanical Engineers (ASME), 1991)An incremental plasticity model is proposed based on the von-Mises yield condition, associated flow rule, and nonlinear kinematic hardening rule. In the present model, fatigue life prediction ... -
A Constitutive Model for Metals Subjected to Cyclic Creep
(The American Society of Mechanical Engineers (ASME), 1991)This paper presents a constitutive model which can be used to predict creep strains and rupture lives of engineering materials undergoing entire creep process, including primary, secondary, and ... -
Computer-Aided Modeling of Polymer Processing: A Review
(The American Society of Mechanical Engineers (ASME), 1991)Polymer processing is increasingly important ever since the rapid growth of polymer applications in the past decade. In this paper, the computational aspects of modeling the polymer behavior ... -
Multishock Compactions of Powder Media Influenced by Elastic Waves in Punch and Plug
(The American Society of Mechanical Engineers (ASME), 1991)The previous theoretical predictions of the compaction of a copper powder medium, based on the assumption that the punch and plug were both a rigid body, did not satisfactorily agree with the ... -
Mechanical Characterization of IM7/8551-7 Carbon/Epoxy Under Biaxial Stress
(The American Society of Mechanical Engineers (ASME), 1990)This paper presents the results of a detailed characterization of the relatively new IM7/8551-7 carbon/epoxy material system under conditions of multiaxial stresses applied to both laminae and ... -
Thermo-Mechanical Fatigue of Mar-M247: Part 2—Life Prediction
(The American Society of Mechanical Engineers (ASME), 1990)A life prediction model is proposed based on microstructural observations of damage in thermo-mechanical fatigue and isothermal fatigue experiments on Mar-M247 Nickel based Superalloy. The model ...