Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1961-1980 of 3257
-
A Micromechanics Model for Thermoelastic Properties of Plain Weave Fabric Composites
(The American Society of Mechanical Engineers (ASME), 1994)A micromechanics model is presented to predict thermoelastic properties of composites reinforced with plain weave fabrics. A representative volume element is chosen for analysis and the fiber ... -
Finite Element Mesh Refinement for Discontinuous Fiber Reinforced Composites
(The American Society of Mechanical Engineers (ASME), 1994)This paper is concerned with the development of a generalized approach for mesh refinement in a short fiber reinforced composite. Mesh refinement procedures are based on the calculation of the ... -
Experimental Characterization of the Tensile Behavior of Microcellular Polycarbonate Foams
(The American Society of Mechanical Engineers (ASME), 1994)Novel polycarbonate (PC) foams with bubbles on the order of 10 μm and cell nucleation densities between 1 and 10 billion cells per cubic centimeter of foam have been produced using carbon ... -
The Transition to Quasi-Periodicity for Molten Plastics in Large Amplitude Oscillatory Shear
(The American Society of Mechanical Engineers (ASME), 1994)Large amplitude oscillatory shear (LAOS) experiments on three grades of LLDPE including one commercial film blowing resin showed an interesting transition in the shear stress response to LAOS. ... -
Detection of 1 mm Fatigue Crack Initiation Using Strain Waveform
(The American Society of Mechanical Engineers (ASME), 1994)It is very difficult to monitor fatigue crack initiation at all parts of machine equipment day after day. In this study, a method of continuous monitoring for fatigue crack initiation is ... -
Numerical Simulation of Fracture in Coated Brittle Materials Subjected to Tribo-Contact
(The American Society of Mechanical Engineers (ASME), 1994)Manufacturing processes used to deposit hard coatings often produce cracks which reside within the coating, at the interface, or in the substrate. These cracks originate from material defects ... -
Parameter Analysis for Time-Dependent Low-Cycle Fatigue Life
(The American Society of Mechanical Engineers (ASME), 1994)Temperature and strain rate dependences of low-cycle fatigue life can be represented by a modified Larson-Miller parameter. The parameter P is written by P=T(logN25 −Alog ε̇ + B), where T is ... -
Effect of CO2 Saturation and Desorption on the Fatigue Life of Polycarbonate
(The American Society of Mechanical Engineers (ASME), 1994)The effect of a cycle of CO2 saturation and desorption on the yield strength, Young’s modulus, and fatigue life of polycarbonate was investigated. The fatigue life of the saturation-cycled ... -
Small Punch Testing for Determining the Material Toughness of Low Alloy Steel Components in Service
(The American Society of Mechanical Engineers (ASME), 1994)The toughness of the low alloy ferritic steel material of structural components operating at elevated temperatures can degrade during service due to embrittling phenomena such as carbide coarsening ... -
Dynamic Crack Growth in a Power Hardening Viscoplastic Material
(The American Society of Mechanical Engineers (ASME), 1994)In this paper a finite element analysis of steady-state dynamic crack growth under mode I plane strain small scale yielding conditions has been performed in a power law hardening rate dependent ... -
The Variable Threshold Rod Experiment: A Comparison of Measured and Computed Deformations
(The American Society of Mechanical Engineers (ASME), 1993)A novel experiment has been developed to induce inhomogeneous deformations under simple extension boundary conditions. By appropriate prior cold working of stock material and fabrication of test ... -
Modeling of Viscoplastic Adhering Process by a Finite Element Technique
(The American Society of Mechanical Engineers (ASME), 1993)The intimate contacting of rough surfaces in the solid state bonding of metals is modeled by a finite element method. The finite element method can be applied to the large deformation process ... -
Machinability of Fiber-Reinforced Thermoplastics in Drilling
(The American Society of Mechanical Engineers (ASME), 1993)Polymer-based composite materials are used in a variety of industry. Recently, thermoplastic polymer suitable for the resinous matrix in carbon fiber-reinforced composites has been introduced for ... -
Finite Element Analysis of Whisker-Reinforced SiC/Al Composites Subjected to Cryogenic Temperature Thermal Cycling
(The American Society of Mechanical Engineers (ASME), 1993)Thermo-elastoplastic finite element methods are used to investigate the thermal cycling of SiC whisker-reinforced aluminum-matrix composites. In a previous investigation, the development of residual ... -
Stress Intensity Factors for Multiple Cracks in an Adhesively Bonded Sandwich Sheet
(The American Society of Mechanical Engineers (ASME), 1993)A new method is proposed for analyzing stress intensity factors of multiple cracks in an adhesively bonded metallic sandwich sheet. Using a basic solution of a single crack and taking unknown ... -
Effect of Fiber Reinforcement on Dynamic Crack Growth in Brittle Matrix Composites
(The American Society of Mechanical Engineers (ASME), 1993)An experimental investigation is conducted to study the interaction of a running crack with embedded fibers. Dynamic photoelasticity is used to evaluate the crack velocity and the instantaneous ... -
In-Situ Compressive Strength of Carbon/Epoxy AS4/3501-6 Laminates
(The American Society of Mechanical Engineers (ASME), 1993)An experimental program has been conducted to evaluate how changes in laminate lay-up can influence the compression behavior of fiber-dominated, resin-based composites. The testing utilized a ... -
Compression Fatigue Response for Carbon Fiber With Conventional and Toughened Epoxy Matrices With Damage
(The American Society of Mechanical Engineers (ASME), 1993)This paper compares the open hole compression, compression after impact, compression fatigue of open hole specimens, and compression fatigue after impact response of quasi-isotropic laminates with ... -
Yield and Flow Behavior of Initially Anisotropic Aluminum Tube Under Multiaxial Stresses
(The American Society of Mechanical Engineers (ASME), 1993)By means of combining Drucker’s yield function with Hill’s quadratic yield function, an anisotropic yield function of the sixth degree is proposed. It is able to include the effects of the ... -
Thermal-Induced Transformation of Retained Austenite in the Simulated Case of a Carburized Steel
(The American Society of Mechanical Engineers (ASME), 1993)Systematic experiments were conducted on carburized 4320 steel to study thermalinduced transformation of austenite to bainite by measuring the volumetric transformation strains. Up to about 210°C, ...