Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1381-1400 of 3257
-
An Improvement of Multiaxial Ratchetting Modeling Via Yield Surface Distortion
(The American Society of Mechanical Engineers (ASME), 2002)Many theoretical studies have been made to describe multiaxial ratchetting and most of them have been concentrated on the location of the yield domain, not on its shape. In this paper, we ... -
Transitions: A Note From the Editor
(The American Society of Mechanical Engineers (ASME), 2002)It seems like only a few years ago that I started my first Associate Editor term with JEMT, but ten years have passed! It has been an honor and privilege for me to serve my term as ... -
Erratum: “A Study of Residual Stresses and Microstructure in 2024-T3 Aluminum Friction Stir Butt Welds” [ASME J. Eng. Mater. Technol., 124, No. 2, pp. 215–222]
(The American Society of Mechanical Engineers (ASME), 2002)Figure 2 on p. 216 of the article does not have the correct dimensions for the Arcan test specimens. The discrepancy can be seen by comparing Fig. 2 to Fig. 6 in the article. The properly ... -
Development of Shape Memory TiNi Fiber Reinforced Epoxy Matrix Composite and Its Properties
(The American Society of Mechanical Engineers (ASME), 2002)Shape memory alloy TiNi fiber epoxy resin composite (SMA-FEC) was developed and the active reinforcement effect of the material was investigated by strain gauge measurement and photoelastic method. ... -
Residual Stress Measurement in Spot Welds and the Effect of Fatigue Loading on Redistribution of Stresses Using High Sensitivity Moiré Interferometry
(The American Society of Mechanical Engineers (ASME), 2001)Residual stress distribution has been determined in spot welds, which are generally used to join mild steel sheets. Various spot weld configurations were investigated using the full-field, ... -
Sheet Forming Analysis Based on Improved Contact Searching Algorithm and Simple Approach for Contact Force Evaluation
(The American Society of Mechanical Engineers (ASME), 2001)Explicit finite element procedures for the simulation of sheet-metal-forming processes are reviewed. Improved techniques for contact searching and contact force evaluation are then proposed and ... -
Analytical and Experimental Studies of Short-Beam Interlaminar Shear Strength of G-10CR Glass-Cloth/Epoxy Laminates at Cryogenic Temperatures
(The American Society of Mechanical Engineers (ASME), 2001)Cryogenic interlaminar beam tests in the form of three-point flexure are examined both experimentally and analytically. The use of the short-beam shear test for measuring the interlaminar shear ... -
Foreword
(The American Society of Mechanical Engineers (ASME), 2001) -
Analyses of Contact Pressure and Stress Amplitude Effects on Fretting Fatigue Life
(The American Society of Mechanical Engineers (ASME), 2001)Elastic-plastic finite element analyses of a cylinder-on-plate configuration, studied experimentally, were performed to provide an explanation for the decrease in fretting fatigue life with increasing ... -
Simulation of Multipass Welding With Simultaneous Computation of Material Properties
(The American Society of Mechanical Engineers (ASME), 2001)Multipass butt welding of two 0.2 m thick steel plates has been investigated. The objective is to calculate residual stresses and compare them with measured residual stresses. The material ... -
Creep Relaxation of Residual Stresses Around Cold Expanded Holes
(The American Society of Mechanical Engineers (ASME), 2001)The cold expansion of fastener holes in aircraft components is a standard technique to improve fatigue life. There is concern that the beneficial residual stresses arising from cold expansion ... -
Wire Coating Under Vacuum
(The American Society of Mechanical Engineers (ASME), 2001)A numerical solution is presented for isothermal Newtonian wire coating under vacuum or with an externally applied pressure. Differential equations for the melt cone shape are derived from a ... -
Upsetting of Cylinders: A Comparison of Two Different Damage Indicators
(The American Society of Mechanical Engineers (ASME), 2001)Two damage indicators for ductile failure, as proposed by Hancock–Mackenzie–Gunawardena and Atkins, are compared with experimental results from literature for the upsetting process of cylindrical ... -
Three Stages of Fatigue Crack Growth in GFRP Composite Laminates
(The American Society of Mechanical Engineers (ASME), 2001)Multiple fatigue crack growth behavior has been studied in model transparent GFRP laminates. Detailed experimental observations have been made on the growth of individual fatigue cracks and on ... -
The Modeling of Unusual Rate Sensitivities Inside and Outside the Dynamic Strain Aging Regime
(The American Society of Mechanical Engineers (ASME), 2001)The viscoplasticity theory based on overstress (VBO) is altered by introducing an augmentation function into the dynamic recovery term of the growth law of the equilibrium stress, which is a ... -
Design and Operation of a Droplet Deposition System for Freeform Fabrication of Metal Parts
(The American Society of Mechanical Engineers (ASME), 2001)A droplet generator has been designed and built to make wax and tin alloy droplets for freeform fabrication. The linear stability theory of liquid jets for forming droplets is first reviewed. ... -
Time Model of Rubber Deformation
(The American Society of Mechanical Engineers (ASME), 2001)In this article we present a simplified time model of elastic deformation in rubber. The originality of the method is to provide a model with very few degrees of freedom while conserving the ... -
Mechanics and Physics of Brittle to Ductile Transitions in Fracture1
(The American Society of Mechanical Engineers (ASME), 2001)The mechanisms of brittle-to-ductile transition of fracture in intrinsically brittle crystalline solids such as structural steel have been of great technological interest for a long time. While ... -
A General Time Dependent Constitutive Model: Part I— Theoretical Developments1
(The American Society of Mechanical Engineers (ASME), 2001)Using an internal-variable formalism as a starting point, we describe the viscoelastic complement of a previously-developed viscoplasticity formulation of the complete potential structure type. It ... -
Influence of Alpha Casing on Superplastic Deformation of Ti-6Al-4V
(The American Society of Mechanical Engineers (ASME), 2001)Impact of alpha casing on the superplastic deformation of Ti-Al-4V was studied by applying an oxygen barrier coating onto the surface prior to superplastic forming and mechanical testing at ...