Journal of Energy Resources Technology: Recent submissions
Now showing items 3401-3420 of 3450
-
Discussion: “Practice of Heat Utilization from Refuse” (Martin, W. J., and Weiand, H., 1980, ASME J. Energy Resour. Technol., 102, pp. 230–233)
(The American Society of Mechanical Engineers (ASME), 1980) -
A Three-Dimensional Anisotropic Yield Condition for Green River Shale
(The American Society of Mechanical Engineers (ASME), 1980)A three-dimensional, transversely isotropic yield condition is combined with a plane of weakness to describe the initial yield limit for Green River Shale. This theory is compared to experimental ... -
Inertia Coefficients for Riser Configurations
(The American Society of Mechanical Engineers (ASME), 1980)Inertia coefficients for arrays of cylinders, such as might be found in risers or conductor pipes, are determined. The method used is theoretical and does not take into account viscous-related ... -
Vibrations of Marine Riser Systems
(The American Society of Mechanical Engineers (ASME), 1980)A discrete multi-degree-of-freedom model is used to study the dynamic response of marine riser systems to loads generated by sea waves and currents. A linearization scheme is used to determine ... -
Higher Pump Pressures Can Reduce Drilling Costs
(The American Society of Mechanical Engineers (ASME), 1979)Deep-well drilling costs can be reduced substantially by using higher mud pump pressures. This has been demonstrated during the drilling of 1267 m (4166 ft) of 12 1/4-in. and 8 1/2-in. hole ... -
Capital Cost System Optimization of OTEC Power Modules
(The American Society of Mechanical Engineers (ASME), 1979)Although the concepts of economic trade-off studies and optimization are well known, they are rarely used in large-scale design studies. The purpose of this paper is to demonstrate the feasibility ... -
Decompression of Gas Pipelines During Longitudinal Ductile Fractures
(The American Society of Mechanical Engineers (ASME), 1979)An understanding is given of how gas pipelines decompress when they burst and fail longitudinally in a ductile mode. Transient gas flow equations expressing conservation of mass, momentum and ... -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1979) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1979) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1979) -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1979) -
A Comparison of the Theories for Predicting Width and Extent of Vertical Hydraulically Induced Fractures
(The American Society of Mechanical Engineers (ASME), 1979)Prediction of fracture dimensions during propagation of a hydraulically induced fracture for well stimulation is essential for the design of a stimulation treatment. During the past decade much ... -
A Stress Gradient Theory of Rock Fracture In Drilling
(The American Society of Mechanical Engineers (ASME), 1979)It seems likely that improvements in drilling mechanics will result from an understanding of the stress and strain fields in the rock. Along with this an understanding of rock fracture under ... -
Effect of a Heat-Conducting Well Casing on Temperature Distribution in an Observation Well
(The American Society of Mechanical Engineers (ASME), 1979)The effect of heat conduction on temperature along the wall of a well casing has been determined by solution of the equations of heat conduction. The casing was assumed to pass vertically ... -
Effects of Strain Hardening on Rock / Bit-Tooth Interaction
(The American Society of Mechanical Engineers (ASME), 1979)The rock/bit-tooth interaction problem has been approximated previously by plasticity analysis of a wedge indenting a half-space. In the previous work the rock, under high confining pressure, was ... -
Calculational Modeling of Explosive Fracture and Permeability Enhancement
(The American Society of Mechanical Engineers (ASME), 1979)With its underground explosion computer codes SOC and TENSOR, the Lawrence Livermore Laboratory is developing a capability for computer code prediction of fracture intensity and permeability ... -
Minimum Spacing of Thermally Induced Cracks in Brittle Solids
(The American Society of Mechanical Engineers (ASME), 1979)When the temperature at the free surface of a linearly elastic brittle half-plane, which is initially uniform throughout the solid, is suddenly reduced by a large amount and then kept constant ... -
Design, Fabrication and Field Test Performance of Slug-Type Diamond Compacts Oil Bits
(The American Society of Mechanical Engineers (ASME), 1979)As part of the General Electric Company’s efforts to obtain design and application data for oil and gas well drill bits using the STRATAPAX(T) blank product, a series of slug-type bits were ... -
Capabilities to Determine Rock Properties at Simulated Geothermal Conditions
(The American Society of Mechanical Engineers (ASME), 1979)To date, a very limited amount of rock property research has been conducted under conditions simulating actual geothermal resource conditions. Consequently, limitations exist in the definition and ... -
Optimization of Power Absorption From Sea Waves
(The American Society of Mechanical Engineers (ASME), 1979)This article presents a generalized procedure for selecting rationally the design parameters of a simple wave power absorption system. The system utilizes a tethered-symmetrical float which rides ...