Now showing items 3261-3280 of 3450

    • Pressure Behavior During Polymer Flow in Petroleum Reservoirs 

      Chi U. Ikoku; H. J. Ramey (The American Society of Mechanical Engineers (ASME), 1982)
      This paper presents solutions of the nonlinear partial differential equation using the Douglas-Jones predictor-corrector method for the numerical solution of nonlinear partial differential equations. ...
    • Specifying Linepipe Suitable for Safe Operation in Sour, Wet Service 

      E. M. Moore; D. A. Hansen (The American Society of Mechanical Engineers (ASME), 1982)
      This paper describes the specifications recommended by the authors for buying linepipe in grades up to X-70 for wet, sour service. The linepipe is tested to verify that it is resistant to ...
    • Well Test Analysis for Enhanced Oil Recovery Projects 

      Chi U. Ikoku (The American Society of Mechanical Engineers (ASME), 1982)
      Recent studies on the transient flow of non-Newtonian fluid in porous media have proposed new well test analysis techniques for non-Newtonian injection wells. This paper extends these new ...
    • A Dynamic Model for Rotary Rock Drilling 

      I. E. Eronini; W. H. Somerton; D. M. Auslander (The American Society of Mechanical Engineers (ASME), 1982)
      A rock drilling model is developed as a set of ordinary differential equations describing discrete segments of the drilling rig, including the bit and the rock. The end segment consists of a ...
    • Stability of a Penny-Shaped Geothermal Reservoir in the Earth’s Crust 

      H. Abé; H. Sekine; S. Kitada (The American Society of Mechanical Engineers (ASME), 1982)
      The theoretical analysis of a penny-shaped geothermal reservoir in the earth’s crust subject to linear tectonic stress gradients has been made on the basis of the three-dimensional theory of ...
    • Minimum Spacing of Thermally Induced Cracks in Brittle Solids: Addendum 

      S. Nemat-Nasser; A. Oranratnachai (The American Society of Mechanical Engineers (ASME), 1982)
      Sharper lower bounds for the minimum spacing of thermally induced tension cracks in brittle half-planes are presented, and four previous [1] numerical estimates are improved.
    • Diffusion of Radon Gas from Uranium Mill Tailings 

      W. F. Phillips; D. A. Bell (The American Society of Mechanical Engineers (ASME), 1982)
      A finite element model is presented which predicts radon diffusion in an n layer composite. The basis functions are obtained from an exact solution to the differential equation for a homogeneous ...
    • An Analytical Examination of the Behavior of Oil Sand Fragments in Heated Streams 

      A. Hanafi; G. A. Karim (The American Society of Mechanical Engineers (ASME), 1982)
      The physical and chemical processes that occur typically within and around an oil sand fragment are considered when the fragment is suddenly introduced into a hot, low-uniform velocity, gaseous ...
    • On Dynamic Fracture of Rock Under Bit Impact Loads 

      I. E. Eronini (The American Society of Mechanical Engineers (ASME), 1982)
      A characterization of the dynamic interaction between an impacting tool and rock is presented. The analysis is based on the concept of rock fracture energy and on simple representations of the ...
    • Subsidence Associated With Single and Multicavities for Underground Coal Gasification 

      J. M. Avasthi; G. J. Harloff (The American Society of Mechanical Engineers (ASME), 1982)
      The three-dimensional theoretical development of Berry and Sales [1] has been extended to bring the subsidence predictions into agreement with the British National Coal Board comprehensive set ...
    • Underwater Cargo Vessel Utilizing Variable Buoyancy System for Gliding Propulsion 

      Z. K. Qi; A. Seireg (The American Society of Mechanical Engineers (ASME), 1982)
      This study deals with investigating the feasibility of an underwater glider capable of carrying cargo for long distances by alternately employing gravity and buoyancy forces for forward propulsion. ...
    • Some Psychometric Aspects of a Hydraulic Air Compressor (HAC) 

      Li-Ting Chen; W. Rice (The American Society of Mechanical Engineers (ASME), 1982)
      In a hydraulic air compressor the air is surrounded by water during the compression process which is virtually isothermal. Depending on the state of the inlet air, the compressor water ...
    • Optimum Design and Control of Self-Supported Wave Energy Systems 

      A. Abuelnaga; A. Seireg (The American Society of Mechanical Engineers (ASME), 1982)
      In a previous paper by the authors [1] a procedure is given for the optimum design of single mass, anchored wave energy generators. The anchoring problem is generally regarded as one of the ...
    • At-Sea Evaluation of a Ram Tensioner for Ocean Deployment and Recovery 

      F. C. Liu; R. Sea (The American Society of Mechanical Engineers (ASME), 1982)
    • Moored Systems Designed to Sense Deep Ocean Earthquakes 

      P. J. Hartman (The American Society of Mechanical Engineers (ASME), 1982)
      The ability to predict earthquakes and tsunamis is becoming increasingly important as world population continues to grow in high-density coastal metropolitan areas. Earthquakes which occur in and ...
    • An Experimental Study of Rotor-Filter Pump Performance 

      K. M. Marshek; M. R. Naji; G. C. Andries (The American Society of Mechanical Engineers (ASME), 1982)
      The performance of a rotor-filter pump has been studied experimentally. To develop an understanding of pump performance, and in particular to discern the mechanism of hydraulic pulsing, flow ...
    • Radial Inflow Expansion Turbines for Power Recovery 

      D. A. Bergmann (The American Society of Mechanical Engineers (ASME), 1982)
      Performance data for single-stage, radial inflow, expansion turbines is presented in a manner to enable the process designer to quickly estimate the amount of power available from a process ...
    • The Impact Energy of a Moored Tanker Under the Action of Regular Waves 

      Yu-Cheng Li (The American Society of Mechanical Engineers (ASME), 1982)
      The influence that factors such as mooring line conditions, fender arrangements, dolphin arrangements, degree of ship loading, waves of long period, wave direction, and wind on the impact energy ...
    • A High-Pressure Swivel for Natural Gas Service and Oscillating Motion in a Marine Environment 

      J. T. Herbert; J. E. Ortloff (The American Society of Mechanical Engineers (ASME), 1982)
      A joint development program has produced a unique flowline swivel for high-pressure natural gas service under continuous, small degree rotation, oscillating service. The swivel uses an elastomeric ...
    • Frost and Ice Formation in the Air Convection Pile Permafrost Protection Device 

      R. L. Reid; E. H. Hudgins; J. S. Onufer (The American Society of Mechanical Engineers (ASME), 1982)
      Experimental studies on frost and ice growth under simulated summer conditions were performed on a 3.0-m (10-ft) model of an air convection pile. The air convection pile is a thermosyphon-type ...