Journal of Energy Resources Technology: Recent submissions
Now showing items 2781-2800 of 3450
-
A Predictive Approach for the Flammability Limits of Methane-Nitrogen Mixtures
(The American Society of Mechanical Engineers (ASME), 1990)The present contribution describes a relatively simple procedure for predicting the lean and rich flammability limits of methane-nitrogen mixtures in air from a knowledge of the composition of ... -
Modeling of the Combustion Process in a Dual Fuel Direct Injection Engine
(The American Society of Mechanical Engineers (ASME), 1990)Analytical methods to provide a guideline for predicting the limit for acceptable power output of dual fuel engines due to the onset of autoignition and knock are described. This is achieved ... -
Unsteady Mass Transfer From Oil Sand Spheres in Convective Streams at Low Reynolds Number
(The American Society of Mechanical Engineers (ASME), 1990)The process of transient mass transfer in and around oil sand spheres was investigated experimentally. Preshaped molded spherical particles of Athabasca oil sands were subjected to hot air streams ... -
General Equations for Pressure Drop for Laminar Flow in Ducts of Arbitrary Cross Sections
(The American Society of Mechanical Engineers (ASME), 1990)This paper presents general equations for pressure drop calculations for developed and developing laminar flow in ducts of arbitrary cross sections. The results obtained from these equations ... -
A Poroelastic PKN Hydraulic Fracture Model Based on an Explicit Moving Mesh Algorithm
(The American Society of Mechanical Engineers (ASME), 1990)This paper describes the mathematical formulation of a Perkins-Kern-Nordgren (PKN) fracture model, that accounts for the existence of poroelastic effects in the reservoir. The poroelastic effects, ... -
A Reservoir Simulation Study of Naturally Fractured Lenticular Tight Gas Sand Reservoirs
(The American Society of Mechanical Engineers (ASME), 1990)The results of parametric studies of two naturally fractured lenticular tight gas reservoirs, Fluvial E-1 and Puludal Zones 3 and 4, of the U.S. Department of Energy Multi-Well Experiment (MWX) ... -
A Water-Gas Relative Permeability Relationship for Tight Gas Sand Reservoirs
(The American Society of Mechanical Engineers (ASME), 1990)This paper presents a new approach for the analyses of laboratory-derived capillary pressure data for tight gas sands. The method uses the fact that a log-log plot of capillary pressure against ... -
Analysis of a Solar Space Cooling System Using Liquid Desiccants
(The American Society of Mechanical Engineers (ASME), 1990)For tropical countries, solar space cooling is an attractive proposition. Dehumidification of air in hot, humid climates is almost as important as cooling. Removal of moisture from the air is ... -
A Knowledge-Based Approach to Preliminary Design of Structures
(The American Society of Mechanical Engineers (ASME), 1990)Computers have been used extensively for the analysis, detailed design and drawing production of structures. However, they have not been utilized effectively in the preliminary design stage. ... -
Erratum: “Concerning the Techniques for Plugging Coning Fluids in Oil Wells” (Journal of Energy Resources Technology, 1990, 112, pp. 157–162)
(The American Society of Mechanical Engineers (ASME), 1990) -
Volatilization and Ignition of Oil Sand Samples During Intermittent Exposure to Hot Low-Velocity Air Streams
(The American Society of Mechanical Engineers (ASME), 1989)The behavior of small oil sand samples was monitored experimentally when subjected repeatedly to low-velocity heated air streams, with either prompt quenching or slow cooling of the samples to ... -
The Effect of Inlet Conditions on the Performance of Wells Turbine
(The American Society of Mechanical Engineers (ASME), 1989)Experimental investigations on the effect of inlet turbulence and flow distortion on the performance of a monoplane and a biplane Wells turbine are reported. The performance of biplane Wells ... -
Field Calibration of Orifice Meters for Natural Gas Flow
(The American Society of Mechanical Engineers (ASME), 1989)This paper presents the orifice calibration results for nominal 15.24, 10.16, and 5.08-cm (6, 4, 2-in.) orifice meters conducted at the Chevron’s Sand Hills natural gas flow measurement facility ... -
Phase Change Heat Transfer During Melting and Resolidification of Melt Around Cylindrical Heat Source(s)/Sink(s)
(The American Society of Mechanical Engineers (ASME), 1989)Melting and resolidification of a phase change material around two cylindrical heat exchangers spaced vertically have been investigated experimentally. Experiments have been performed to examine ... -
A Critical Review of Second Law Costing Methods—II: Calculus Procedures
(The American Society of Mechanical Engineers (ASME), 1989)The following article completes the review of the development and state of engineering economic applications of the Second Law of Thermodynamics, which was begun in Part I (El-Sayed and Gaggioli, ... -
Effects of Location and Direction of Diluent Injection on Radiation and Pollutant Emissions of a Burning Spray
(The American Society of Mechanical Engineers (ASME), 1989)Introduction of diluents into diffusion flames is an effective method of changing their combustion and pollutant emission characteristics. Since the dominant thermochemical processes vary from ... -
A Critical Review of Second Law Costing Methods—I: Background and Algebraic Procedures
(The American Society of Mechanical Engineers (ASME), 1989)The following report reviews the development and state of engineering economic applications of the second law of thermodynamics. It encompasses virtually all of the work carried out publicly in ... -
A Study of Mass Transfer Around Oil Sand Fragments in High Temperature Atmospheres
(The American Society of Mechanical Engineers (ASME), 1989)An approximate approach was formulated to estimate the coefficient of convective mass transfer from small preshaped rectangular fragments of oil sands when subjected to hot streams of products ... -
Discontinuities in the Orkiszewski Correlation for Predicting Pressure Gradients in Wells
(The American Society of Mechanical Engineers (ASME), 1989)The Orkiszewski correlation is used extensively in the petroleum industry for predicting pressure gradients when gas and liquid flow simultaneously in wells. Unfortunately, the correlation contains ... -
The Flammability of Fuel Mixtures in Air Containing Propane and Butane
(The American Society of Mechanical Engineers (ASME), 1989)The behavior of the lean and rich flammability limits of various fuel mixture combinations involving propane, n-butane, propylene and ethylene, which feature prominently in a variety of industrial ...