Journal of Energy Resources Technology: Recent submissions
Now showing items 2641-2660 of 3450
-
Closure to “Discussion of ‘Pleasant Bayou Geopressured-Geothermal Reservoir Analysis—October 1991’” (1993, ASME J. Energy Resour. Technol., 115, p. 237)
(The American Society of Mechanical Engineers (ASME), 1993) -
A Leak Localization Method of Pipeline by Means of Fluid Transient Model
(The American Society of Mechanical Engineers (ASME), 1993)This paper describes a method for estimating the position of a detected leak by applying a fluid transient model to a real-time pipeline system. The method takes into account flow rate and ... -
Environmental and Energy Efficiency Evaluation of Residential Gas and Heat Pump Heating
(The American Society of Mechanical Engineers (ASME), 1993)Energy efficiency and source air pollutant emission factors of gas heaters, gas engine heat pumps, and electric heat pumps for domestic heating have been evaluated and compared. The analysis ... -
Mathematical Modeling of PDC Bit Drilling Process Based on a Single-Cutter Mechanics
(The American Society of Mechanical Engineers (ASME), 1993)An analytical development of a new mechanistic drilling model for polycrystalline diamond compact (PDC) bits is presented. The derivation accounts for static balance of forces acting on a single ... -
A Correlation for the Heat Conduction Effects in Counterflow Rotary Regenerative Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 1993)Equations that predict the dependence of regenerator effectiveness on heat conduction in the matrix both parallel to and perpendicular to the fluid flow are derived from numerical simulations. ... -
An Investigation of Water as a Refrigerant
(The American Society of Mechanical Engineers (ASME), 1993)This paper explores some of the basic thermodynamic and technical considerations involved in using water as a working fluid for refrigeration and heat pump cycles down to its freezing point ... -
An Experimental Verification of a Conceptual Heat-Pipe Radiator
(The American Society of Mechanical Engineers (ASME), 1993)The radiator and its vulnerability to damage is one of the main criteria in automotive design. This study employed heat pipes in simulated radiators to transfer waste heat to the surrounding ... -
Analytical and Experimental Investigation of Entrainment in Capillary Pumped Wicking Structures
(The American Society of Mechanical Engineers (ASME), 1993)Analytical and experimental investigations were conducted to identify and better understand the parameters that govern the entrainment of liquid droplets in high-velocity gas streams flowing over ... -
Minimum-Cost Well Drilling Strategy Using Dynamic Programming
(The American Society of Mechanical Engineers (ASME), 1993)This paper presents an advanced concept in drilling optimization—the dynamic drilling strategy. The dynamic drilling strategy is a new methodology of drilling process planning and control; it ... -
Influence of Downstream Distance on the Drop Size Characteristics of an Evaporative Liquid Spray in a Convective Gaseous Medium
(The American Society of Mechanical Engineers (ASME), 1992)Numerical studies have been made to evaluate the interdependence of drop size characteristics and evaporation histories of an atomized liquid spray in a convective medium of uniform free stream ... -
The Component Equations of Energy and Exergy
(The American Society of Mechanical Engineers (ASME), 1992)Energy conversion processes inherently have associated irreversibility. A better understanding of energy conversion will motivate intuition to create new energy-conversion and energy-utilization ... -
Thermodynamic Optimization of Phase-Change Energy Storage Using Two or More Materials
(The American Society of Mechanical Engineers (ASME), 1992)This paper documents the relative merits of using more than one type of phase-change material for energy storage. In the case of two phase-change systems in series, which are melted by the ... -
Application of Strain Space Plasticity Theory to Surface Strain Gage Measurements
(The American Society of Mechanical Engineers (ASME), 1992)Taking strain as the independent variable, the strain space plasticity theory introduced by Naghdi and Trapp is applied to the problem of interpreting strain gage readings for load paths that ... -
The Advantages of Combining Hydraulic and Thermal Energy in Power Plants
(The American Society of Mechanical Engineers (ASME), 1992)Power generation, especially that of electricity, must simultaneously meet the requirements of being able to satisfy peak demands and being easily modulable, even over short periods. The combined ... -
Flammability Characteristics of Treated Coals
(The American Society of Mechanical Engineers (ASME), 1992)The effects of two processes used to treat coal on the flammability characteristics of the coal are presented. Experiments were conducted on an Entrained Dust Flow Facility which supports a ... -
A Model for the Effect of Velocity on Erosion of N80 Steel Tubing due to the Normal Impingement of Solid Particles
(The American Society of Mechanical Engineers (ASME), 1992)As part of a combined experimental and computational study of erosion for gas and oil production conditions, a semi-empirical model has been developed to predict erosion ratio behaviors of ... -
Upward Vertical Two-Phase Flow Through an Annulus—Part II: Modeling Bubble, Slug, and Annular Flow
(The American Society of Mechanical Engineers (ASME), 1992)Mechanistic models have been developed for each of the existing two-phase flow patterns in an annulus, namely bubble flow, dispersed bubble flow, slug flow, and annular flow. These models are ... -
The Effect of Waves on the Oil Slick at a Retention Boom
(The American Society of Mechanical Engineers (ASME), 1992)In the previous paper on this subject it was found that the oil-water interface at the retention boom becomes unstable under certain conditions permitting an oil escape under the boom. In the ... -
Analysis of the Inflow and Pressure Buildup Under Impending Blowout Conditions
(The American Society of Mechanical Engineers (ASME), 1992)In this study a technique is provided for determining formation pore pressure and flow properties based upon analysis of shut-in drill pipe pressure. Both radial and spherical transient flow ... -
Selection of Expert System Development Tools for Engineering Applications
(The American Society of Mechanical Engineers (ASME), 1992)The problems associated with engineering tasks are often too large and complex for application of conventional software methods, but are suitable to application of expert system methods. Development ...