Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 4201-4220 of 5605
-
Global Active Noise Control of a One-Dimensional Acoustic Duct Using a Feedback Controller
(The American Society of Mechanical Engineers (ASME), 1993)Active noise control of acoustic enclosures is a classical engineering problem. The active noise control of a one-dimensional hard-walled duct with a partially dissipative boundary condition is ... -
Detection of Cracks in Turborotors—A New Observer Based Method
(The American Society of Mechanical Engineers (ASME), 1993)The clear relation between shaft cracks in turborotors and vibration effects measured in bearings can be established by model-based methods very well. Here a new concept has been presented, ... -
Time-Optimal Control of Two Robots Holding the Same Workpiece
(The American Society of Mechanical Engineers (ASME), 1993)An algorithm is given which minimizes the time for two robots holding the same workpiece to move along a given path. The unique feature of these systems is that they have more actuators ... -
Dynamic System Synthesis With a Bond Graph Approach: Part I—Synthesis of One-Port Impedances
(The American Society of Mechanical Engineers (ASME), 1993)This is the first part of a two-part paper developing a procedure for impedance synthesis and dynamic system conceptual design using a bond graph approach. The first part examines impedance ... -
Sequential Adaptation in Estimating Elastic Boundary-Condition Influence Matrices
(The American Society of Mechanical Engineers (ASME), 1993)A method is discussed for adaptive estimation of the boundary-condition influence matrix of a linear elastic system, based on modal measurements (eigenvalues and eigenvectors) and on knowledge ... -
Feedforward Tracking Controller Design Based on the Identification of Low Frequency Dynamics
(The American Society of Mechanical Engineers (ASME), 1993)Several methodologies are proposed for identifying the dynamics of a machine tool feed drive system in the low frequency region. An accurate identification is necessary for the design of a ... -
Stability Analysis of a Bilateral Teleoperating System
(The American Society of Mechanical Engineers (ASME), 1993)In this paper the stability of a control scheme for bilateral master-slave teleoperation is investigated. Given the nominal models of the master and slave dynamics, and using an approximate ... -
Real Time Estimation of Elastic Deformation for End-Point Tracking Control of Flexible Two-Link Manipulators
(The American Society of Mechanical Engineers (ASME), 1993)In this paper, an elastic-deformation estimator is proposed for real time end-point tracking control of a flexible two-link manipulator. Due to the noncolocated characteristics of the system, the ... -
Sensor Failure Detection in Flexible Structures Using Modal Observers
(The American Society of Mechanical Engineers (ASME), 1993)A procedure is developed to detect sensor failures in flexible structures by means of observers designed at the modal level. Estimates of the modal coordinates generated by the modal observers ... -
Dynamic System Synthesis With a Bond Graph Approach: Part II—Conceptual Design of an Inertial Velocity Indicator
(The American Society of Mechanical Engineers (ASME), 1993)This work develops the conceptual design of an inertial velocity sensor drawing upon the impedance synthesis method in Part I of this paper. Specifications are frequency based impedances and ... -
An End-Time Constrained Receding Horizon Control Policy
(The American Society of Mechanical Engineers (ASME), 1993)A predictive control policy that utilizes a finite time horizon with end-time constraints is described. The control law minimizes actuator movement while satisfying both process and control output ... -
Shaped Input Control of a System With Multiple Modes
(The American Society of Mechanical Engineers (ASME), 1993)This paper describes a method for limiting vibration in flexible systems that have more than one characteristic frequency and mode. It is only necessary to have knowledge of the component mode ... -
Approximate Optimal Trajectories for Flexible-Link Manipulator Slewing Using Recursive Quadratic Programming
(The American Society of Mechanical Engineers (ASME), 1993)The method of recursive quadratic programming, coupled with a homotopy method, has been used to generate approximate minimum-time and minimum tracking-error tip trajectories for two-link flexible ... -
Active and passive Damping of Euler-Bernoulli Beams and Their Interactions
(The American Society of Mechanical Engineers (ASME), 1993)Active and Passive damping of Euler-Bernoulli beams and their interactions have been studied using the beam’s exact transfer function model without mode truncation or finite element or finite ... -
Centralized Control of n Identical Plants
(The American Society of Mechanical Engineers (ASME), 1993)In an elegant and yet easily comprehensible and applicable way, it is shown how the outputs of n identical plants G(s) = K/ sp l=1μ (s+al) with different output initial conditions can be ... -
Dynamics of Flexible Manipulator Arms: Alternative Derivation, Verification, and Characteristics for Control
(The American Society of Mechanical Engineers (ASME), 1993)This work seeks to provide an effective way for developing the dynamics of a multi-link flexible manipulator consisting of rotary joints connecting two links. Kinematics of both the rotary joint ... -
Parameter Identification of Compressor Dynamics During Closed-Loop Operation
(The American Society of Mechanical Engineers (ASME), 1993)A low-speed axial research compressor has been fitted with movable inlet guide vanes to allow for feedback stabilization of rotating stall. A model exists whose structure captures the input-output ... -
Control-Oriented Order Reduction of Finite Element Model
(The American Society of Mechanical Engineers (ASME), 1993)In the dynamics modeling of a structure, finite element analysis employs reduction techniques, such as Guyan’s reduction, that remove some of the “insignificant” physical coordinates, that is, ... -
Inertia Matrix Singularity of Series-Chain Spatial Manipulators With Point Masses
(The American Society of Mechanical Engineers (ASME), 1993)Often, the dynamic behavior of multi-degree-of-freedom mechanical systems such as robots and manipulators is studied by computer simulation. An important step in this simulation is the inversion ... -
An Iterative Approach to Multibody Simulation Dynamics Suitable for Parallel Implementation
(The American Society of Mechanical Engineers (ASME), 1993)This paper presents a new solution procedure for simulation dynamics of multibody systems. The method is applicable to open chains with general interbody constraints. It is based on obtaining ...