Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 3701-3720 of 5605
-
Erratum: “A Higher-Order Method for Dynamic Optimization of a Class of Linear Systems” [ASME JOURNAL OF DYNAMIC SYSTEMS, MEASUREMENT, AND CONTROL, 1996, 118(4), pp. 786–791]
(The American Society of Mechanical Engineers (ASME), 1997) -
System Dynamics Modeling of Porous Media
(The American Society of Mechanical Engineers (ASME), 1997)A wide range of engineering problems involve porous media modeling. General porous media models are highly nonlinear, geometrically complex, and must account for energy transfer between fluid and ... -
Coupling Between the Modeling and Controller-Design Problems—Part II: Design
(The American Society of Mechanical Engineers (ASME), 1997)In Part I of this paper, the coupling between the modeling and controller-design problems was quantified in terms of the size of the set of models from which satisfactory controllers may be ... -
Assessing the Potential for Energy Regeneration in Dynamic Subsystems
(The American Society of Mechanical Engineers (ASME), 1997)The utility of many controlled dynamic systems is impaired by excessive power consumption and related hardware. In this paper, the potential for energy regeneration in a broad class of dynamic ... -
An LQ Controller With a Prescribed Pole Region—A Data-Based Design Approach
(The American Society of Mechanical Engineers (ASME), 1997)In this paper, we present a modified method of data-based LQ controller design which is distinct in two major aspects: (1) one may prescribe the z-domain region within which the closed-loop ... -
The Role of Environment Dynamics in Contact Force Control of Manipulation Robots
(The American Society of Mechanical Engineers (ASME), 1997)This paper draws attention to the role of the environment dynamics in force control of robots interacting with dynamic environment. Traditional control approaches are based on restrictive ... -
Land Vehicle Roll/Yaw Product of Inertia Measurement
(The American Society of Mechanical Engineers (ASME), 1997)This paper focuses on the measurement of the roll/yaw product of inertia of a vehicle and describes a four-degree-of-freedom lumped-parameter ADAMS model used to simulate the test configuration. ... -
The Shape From Motion Approach to Rapid and Precise Force/Torque Sensor Calibration
(The American Society of Mechanical Engineers (ASME), 1997)We present a new technique for multi-axis force/torque sensor calibration called shape from motion. The novel aspect of this technique is that it does not require explicit knowledge of the ... -
Robustness of Adaptive Rotor Vibration Control to Structured Uncertainty
(The American Society of Mechanical Engineers (ASME), 1997)Recent experimental results have demonstrated the effectiveness of adaptive open-loop control algorithms for the suppression of unbalance response on rotors supported in active magnetic hearings. ... -
Multivariable Trend Analysis for System Monitoring Through Self-Organizing Neural Networks
(The American Society of Mechanical Engineers (ASME), 1997)For precise and reliable fault detection it is essential to consider simultaneously the changes in several diagnostic indices that are extracted from the on-line vibration signal. Existing machine ... -
Constrained H∞ Control of an Experimental Flexible Link
(The American Society of Mechanical Engineers (ASME), 1997)A new approach is presented to design robust controllers for an experimental flexible beam with noncolocated sensors-actuator. The objective is to position the free end of the beam in the ... -
A Non-Normality Measure of the Condition Number for Monitoring and Control
(The American Society of Mechanical Engineers (ASME), 1997)Because the behavior of the condition number can have highly steep and multi-modal structure, optimal control and monitoring problems based on the condition number cannot be easily solved. In ... -
Time-Optimal Negative Input Shapers
(The American Society of Mechanical Engineers (ASME), 1997)Input shaping reduces residual vibration in computer controlled machines by convolving a sequence of impulses with a desired system command. The resulting shaped input is then used to drive the ... -
Cross Calibration by FFT Equalization
(The American Society of Mechanical Engineers (ASME), 1997)The classical calibration problem is primarily concerned with comparing an approximate measurement method with a very precise one. Frequently, both measurement methods are very noisy, so we cannot ... -
Robot Obstacle Avoidance in n-Dimensional Space Using Planar Harmonic Artificial Potential Fields
(The American Society of Mechanical Engineers (ASME), 1997)Autonomous operation of robots requires on-line obstacle avoidance. A wide-spread tool for obstacle avoidance, employed both for mobile robots and for manipulator arms, is the artificial potential ... -
Distributed Link-Layer Control for Automated Highway Systems
(The American Society of Mechanical Engineers (ASME), 1997)The modeling and design of a link-layer control algorithm for automated highway systems are presented in this paper. Link-layer control systems address the coordination of traffic on a stretch ... -
A Digital Robust Controller for Cutting Force Control in the End Milling Process
(The American Society of Mechanical Engineers (ASME), 1997)In this work, a digital robust controller is designed via Quantitative Feedback Theory (QFT) to maintain a constant cutting force in the presence of parametric uncertainty for a time varying ... -
Advanced Control Design for Marine Diesel Engine Propulsion Systems
(The American Society of Mechanical Engineers (ASME), 1997)A new marine diesel engine propulsion control design procedure is proposed which is applicable to a wide range of marine vessels. This procedure combines linear optimal H∞ control methods with ... -
Design of Optimal MIMO DIVSC Systems and Its Application to Idle Speed Control of Spark Ignition Engine
(The American Society of Mechanical Engineers (ASME), 1997)An optimal multi-input multi-output (MIMO) discrete integral variable structure control (DIVSC) rule is proposed in this paper. This approach can achieve accurate and robust dynamic responses. The ... -
Modeling of Vapor Compression Cycles for Multivariable Feedback Control of HVAC Systems
(The American Society of Mechanical Engineers (ASME), 1997)This paper presents a new lumped-parameter model for describing the dynamics of vapor compression cycles. In particular, the dynamics associated with the two heat exchangers, i.e., the evaporator ...