Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 3341-3360 of 5605
-
A Unified Approach to Driver Assistance Systems Based on Artificial Potential Fields
(The American Society of Mechanical Engineers (ASME), 2001)This paper presents an approach to vehicle control based on the paradigm of artificial potential fields. Using this method, the dynamics of the vehicle are coupled with the environment in a ... -
Transparency and Stability Robustness in Two-Channel Bilateral Telemanipulation
(The American Society of Mechanical Engineers (ASME), 2001)This paper presents a two-channel architecture and design approach that enables a simultaneous increase in the transparency and stability robustness of a bilateral teleoperation system, and ... -
Lapping Control of Hard Disk Drive Heads
(The American Society of Mechanical Engineers (ASME), 2001)Bar lapping is a key process in fabricating computer hard disk drive heads. The purpose is to remove a small amount of material so that the transducer stripe height variation across the bar ... -
Design of a Nonlinear Adaptive Controller for an Electrohydraulic Actuator1
(The American Society of Mechanical Engineers (ASME), 2001)This paper presents a new implementation of indirect model reference adaptive (MRA) control scheme for positioning of hydraulic actuators that operate by low-cost proportional valves. A proper ... -
Combining a Multirate Repetitive Learning Controller With Command Shaping for Improved Flexible Manipulator Control
(The American Society of Mechanical Engineers (ASME), 2001)Comand shaping, a feedforward approach used to control flexible manipulators, performs most effectively when applied to a linear system. In practice, various nonlinearities are present in a given ... -
A New Mechanism Explaining High Frequency Chatter Vibration Involving Tool Tip X-Y Looping in Fine Boring
(The American Society of Mechanical Engineers (ASME), 2001)Chatter occurring at more than 10,000 Hz frequency was found in fine boring operation, and causing reduced tool life. To identify the mechanism for the onset of high frequency chatter, cutting ... -
Application of H∞ Control to Improve the Current and Speed Loops of Switched Reluctance Motor Drives
(The American Society of Mechanical Engineers (ASME), 2001)In this paper the H∞ robust control technique is applied to design a switched reluctance motor drive where the rotor position sensor provides just six pulses per revolution. A control system ... -
Robust Performance Repetitive Control Systems
(The American Society of Mechanical Engineers (ASME), 2001)This paper addresses analysis and synthesis of robust stability and robust performance repetitive control systems. The repetitive control design problem is formulated as a standard feedback form ... -
Sliding Control of Magnetic Bearing Systems
(The American Society of Mechanical Engineers (ASME), 2001)This paper proposes a sliding control scheme to deal with the nonlinear, uncertain dynamics of magnetic bearing systems. The controller is designed based on the Thevenin equivalent of a network ... -
Application of an Optimal Control Synthesis Strategy to an Electro-Hydraulic Positioning System
(The American Society of Mechanical Engineers (ASME), 2001)Successive Galerkin Approximation (SGA) provides a means for approximating solutions to the Hamilton-Jacobi-Bellman (HJB) equation. The SGA strategy is applied to the development of optimal control ... -
A Recursive Multibody Dynamics and Sensitivity Algorithm for Branched Kinematic Chains
(The American Society of Mechanical Engineers (ASME), 2001)In this work an efficient dynamics algorithm is developed, which is applicable to a wide range of multibody systems, including underactuated systems, branched or tree-topology systems, robots, ... -
H∞-Based Robust Torque Control of Harmonic Drive Systems
(The American Society of Mechanical Engineers (ASME), 2001)In this paper, the torque control of a harmonic drive system for constrained-motion and free-motion applications is examined in detail. A nominal model for the system is obtained in each case ... -
Adaptive Control of Active Balancing Systems for Speed-Varying Rotors Using Feedforward Gain Adaptation Technique
(The American Society of Mechanical Engineers (ASME), 2001)This paper presents a new adaptive control method for active balancing of speed-varying rotors. It is developed based on the feedforward gain adaptation problem, which is a classical technique ... -
An Input-Output Linearization Approach to the Control of an n-Body Articulated Vehicle
(The American Society of Mechanical Engineers (ASME), 2001)The problem of path-tracking for an autonomous vehicle composed of a tractor and n−1 trailers with off-axle hitching is considered in this paper. It is shown that an input-output feedback ... -
Structural Health Monitoring Using Statistical Pattern Recognition Techniques
(The American Society of Mechanical Engineers (ASME), 2001)This paper casts structural health monitoring in the context of a statistical pattern recognition paradigm. Two pattern recognition techniques based on time series analysis are applied to fiber ... -
Asymptotic Rejection of Periodic Disturbances With Fixed or Varying Period
(The American Society of Mechanical Engineers (ASME), 2001)A constructive derivation of repetitive control is obtained, through attempting to derive a control law for asymptotic rejection of periodic disturbances. This derivation not only reveals a close ... -
Output Feedback Second-Order Sliding Mode Control for a Class of Nonlinear Systems With Non-Matched Uncertainties
(The American Society of Mechanical Engineers (ASME), 2001)The problem of the design of an output feedback second-order sliding mode control for a class of nonlinear systems affine in the control law with non-matched uncertainties is considered in ... -
Tuning of a Hard Disk Drive Servo Controller Using Fixed-Structure H∞ Controller Optimization
(The American Society of Mechanical Engineers (ASME), 2001)As the storage capacity of hard disk drives (HDDs) increases dramatically, the demand for positioning control accuracy of a read/write head of HDD is becoming more stringent. This paper presents ... -
Model Based Damage Identification Using Output Spectral Densities
(The American Society of Mechanical Engineers (ASME), 2001)A damage identification method utilizing an existing computational model and output spectral densities is presented. The problem covered here is the detection, localization and quantification of ... -
Optimal Sensor Placement Methodology for Identification with Unmeasured Excitation
(The American Society of Mechanical Engineers (ASME), 2001)A methodology is presented for designing cost-effective optimal sensor configurations for structural model updating and health monitoring purposes. The optimal sensor configuration is selected such ...