Journal of Dynamic Systems, Measurement, and Control: Recent submissions
Now showing items 2381-2400 of 5605
-
A Comparative Analysis of Energy Management Strategies for Hybrid Electric Vehicles
(The American Society of Mechanical Engineers (ASME), 2011)This paper presents a formalization of the energy management problem in hybrid electric vehicles and a comparison of three known methods for solving the resulting optimization problem. Dynamic ... -
An Adaptive Multi-Objective Controller for Flexible Rotor and Magnetic Bearing Systems
(The American Society of Mechanical Engineers (ASME), 2011)This paper considers two issues in the vibration of rotating machines, namely, control of rotor vibration and control of the forces transmitted to the base. An adaptive multi-objective method ... -
Identification of Tire Model Parameters Through Full Vehicle Experimental Tests
(The American Society of Mechanical Engineers (ASME), 2011)Individual tire model parameters are traditionally derived from expensive component indoor laboratory tests as a result of an identification procedure minimizing the error with respect to force ... -
Switch-Mode Continuously Variable Transmission: Modeling and Optimization
(The American Society of Mechanical Engineers (ASME), 2011)Hybrid vehicles are an important step toward reducing global petroleum consumption and greenhouse gas emissions. Flywheel energy storage in a hybrid vehicle combines high energy density and high ... -
Fault Diagnosis of High Speed Rolling Element Bearings Due to Localized Defects Using Response Surface Method
(The American Society of Mechanical Engineers (ASME), 2011)In this paper, fault diagnosis of high speed rolling element bearings due to localized defects using response surface method has been done. The localized defects as spalls on outer race, on ... -
Modified Generalized Predictive Control of Networked Systems With Application to a Hydraulic Position Control System
(The American Society of Mechanical Engineers (ASME), 2011)This paper is concerned with the design of networked control systems using the modified generalized predictive control (M-GPC) method. Both sensor-to-controller (S-C) and controller-to-actuator (C-A) ... -
A Model-Based Methodology for Real-Time Estimation of Diesel Engine Cylinder Pressure
(The American Society of Mechanical Engineers (ASME), 2011)Cylinder pressure is one of the most important parameters characterizing the combustion process in an internal combustion engine. The recent developments in engine control technologies suggest the ... -
Dead-Time Compensation for Wave/String PDEs
(The American Society of Mechanical Engineers (ASME), 2011)Smith predictorlike designs for compensation of arbitrarily long input delays are commonly available only for finite-dimensional systems. Only very few examples exist, where such compensation has ... -
Modeling Identification and Control of Peltier Thermoelectic Modules for Telepresence
(The American Society of Mechanical Engineers (ASME), 2011)This research deals with thermal rendering for telepresence applications. We present the modeling and identification of thermo-electric modules (TEMs) to be used either as part of a thermal ... -
Active Control of Vehicle Transient Powertrain Noise Using a Twin-FXLMS Algorithm
(The American Society of Mechanical Engineers (ASME), 2011)Powertrain noise is a major component of vehicle interior noise and thus has a significant effect on the overall sound quality. It is typically dominated by harmonics in the lower audible ... -
Suitability of Redesigned Digital Control Systems Having an Interval Plant via an Evolutionary Approach
(The American Society of Mechanical Engineers (ASME), 2011)In this paper, a quantitative index is proposed to address the performance evaluation and design issues in the digital redesign of continuous-time interval systems. From the perspective of signal ... -
A Validated Modular Model for Hydraulic Actuation in a Pushbelt Continuously Variable Transmission
(The American Society of Mechanical Engineers (ASME), 2011)A reduction in the fuel consumption of a passenger car with a pushbelt continuously variable transmission (CVT) can be established via optimization of the hydraulic actuation system. This requires ... -
The Electromechanical Low-Power Active Suspension: Modeling, Control, and Prototype Testing
(The American Society of Mechanical Engineers (ASME), 2011)The high energy consumption of market-ready active suspension systems is the limiting factor in the competition with semi-active devices. The variable geometry active suspension is an alternative ... -
Performance Measure of Residual Vibration Control
(The American Society of Mechanical Engineers (ASME), 2011)The robustness of residual vibration control, such as input shaping, has conventionally been evaluated from the ratio of residual vibration amplitude with input shaping to that without input ... -
Transformation of a Mismatched Nonlinear Dynamic System into Strict Feedback Form
(The American Society of Mechanical Engineers (ASME), 2011)Dynamic surface control is a robust nonlinear control technique. It is generally applied to mismatched dynamic systems in strict feedback form. We have developed a new method of defining states ... -
Source Seeking With Very Slow or Drifting Sensors
(The American Society of Mechanical Engineers (ASME), 2011)Slow sensors arise in many applications, including sensing chemical concentrations in tracking of contaminant plumes. Slow sensors are often the cause of poor performance and a potential cause ... -
NO and NO2 Concentration Modeling and Observer-Based Estimation Across a Diesel Engine Aftertreatment System
(The American Society of Mechanical Engineers (ASME), 2011)This paper presents an experimentally validated control-oriented model and an observer for diesel oxidation catalyst (DOC)-diesel particulate filter (DPF) system in the context of exhaust gas NO ... -
Delay-Dependent L1 Filtering for LPV Systems With Parameter-Varying Delays
(The American Society of Mechanical Engineers (ASME), 2011)The paper investigates the problems of delay-dependent L1 filtering for linear parameter-varying (LPV) systems with parameter-varying delays, in which the state-space data and the time delays are ... -
Output Regulation for Output Feedback Systems With iISS Inverse Dynamics
(The American Society of Mechanical Engineers (ASME), 2011)This paper develops an approach to dealing with the global robust output regulation problem for a class of nonlinear systems with integral input-to-state stable (iISS) inverse dynamics by using ... -
Estimation of Road Friction Coefficient Based on the Brush Model
(The American Society of Mechanical Engineers (ASME), 2011)Road friction coefficients are highly effective for advanced vehicle control technologies, although the estimation at four individual tires has not been practically used for ordinary vehicles. ...