Journal of Heat Transfer: Recent submissions
Now showing items 2901-2920 of 3611
-
Computational Analysis of Pin-Fin Arrays Effects on Internal Heat Transfer Enhancement of a Blade Tip Wall
(The American Society of Mechanical Engineers (ASME), 2010)Cooling methods are strongly needed for the turbine blade tips to ensure a long durability and safe operation. Improving the internal convective cooling is therefore required to increase the ... -
On the Mach Number Invariance of Gas Jets Expanding Into Hot or Cold Environments
(The American Society of Mechanical Engineers (ASME), 2010)Gas jet flows expanding into a space containing the same medium but at a significant temperature difference are of concern in many fields of engineering. One such example is the expansion of ... -
Investigations on Multimode Heat Transfer From a Heated Vertical Plate
(The American Society of Mechanical Engineers (ASME), 2010)The interaction of surface radiation and conduction with natural convection heat transfer from a vertical flat plate assembly, with an embedded heater, has been investigated, both experimentally ... -
Equilibrium Molecular Dynamics Study of Lattice Thermal Conductivity/Conductance of Au-SAM-Au Junctions
(The American Society of Mechanical Engineers (ASME), 2010)In this paper, equilibrium molecular dynamics simulations were performed on Au-SAM (self-assembly monolayer)-Au junctions. The SAM consisted of alkanedithiol (–S–(CH2)n–S–) molecules. The out-of-plane ... -
Flow Visualization and Local Measurement of Forced Convection Heat Transfer in a Microtube
(The American Society of Mechanical Engineers (ASME), 2010)The pressure drop and the convective heat transfer characteristics of ethanol and water in a circular tube with a diameter of 600 μm with and without phase change have been studied experimentally. ... -
Ultra-Low Thermal Conductivity in Nanoscale Layered Oxides
(The American Society of Mechanical Engineers (ASME), 2010)The cross-plane thermal conductivity of several nanoscale layered oxides SiO2/Y2O3, SiO2/Cr2O3, and SiO2/Al2O3, synthesized by e-beam evaporation was measured in the range from 30 K to 300 K by ... -
Fluorescence and Fiber-Optics Based Real-Time Thickness Sensor for Dynamic Liquid Films
(The American Society of Mechanical Engineers (ASME), 2010)To overcome the limitations/disadvantages of many known liquid film thickness sensing devices (viz. conductivity probes, reflectance based fiber-optics probes, capacitance probes, etc.), a new liquid ... -
A Hybrid Method for Measuring Heat Flux
(The American Society of Mechanical Engineers (ASME), 2010)The development and evaluation of a novel hybrid method for obtaining heat flux measurements is presented. By combining the spatial and temporal temperature measurements of a heat flux sensor, ... -
Flow Boiling Visualization of R-134a in a Vertical Channel of Small Diameter
(The American Society of Mechanical Engineers (ASME), 2010)The present work reports on flow boiling visualization of refrigerant R-134a in a vertical circular channel with an internal diameter of 1.33 mm and 235 mm in heated length. A quartz tube ... -
Confocal Microscopy for Capillary Film Measurements in a Flat Plate Heat Pipe
(The American Society of Mechanical Engineers (ASME), 2010)This paper aims to show how confocal microscopy can be useful for characterizing menisci in a flat plate heat pipe made of silicon. The capillary structure is made of radial microgrooves whose ... -
Convection Calibration of Schmidt–Boelter Heat Flux Gauges in Stagnation and Shear Air Flow
(The American Society of Mechanical Engineers (ASME), 2010)Experiments were performed to characterize the performance of Schmidt–Boelter heat flux gauges in stagnation and shear convective air flows. The gauges were of a standard design (25.4 mm and ... -
Analysis of Bioheat Transport Through a Dual Layer Biological Media
(The American Society of Mechanical Engineers (ASME), 2010)A comprehensive analysis of bioheat transport through a double layer and multilayer biological media is presented in this work. Analytical solutions have been developed for blood and tissue phase ... -
Investigation Into the Similarity Solution for Boundary Layer Flows in Microsystems
(The American Society of Mechanical Engineers (ASME), 2010)An investigation toward the existence of a complete similarity solution for boundary layer flows under the velocity slip and temperature jump conditions is carried out. The study is limited to ... -
Representative Results for Condensation Measurements at Hydraulic Diameters ∼100 Microns
(The American Society of Mechanical Engineers (ASME), 2010)Condensation pressure drops and heat transfer coefficients for refrigerant R134a flowing through rectangular microchannels with hydraulic diameters ranging from 100 μm to 200 μm are measured in ... -
Experimental Investigation of Single-Phase Microjet Array Heat Transfer
(The American Society of Mechanical Engineers (ASME), 2010)The heat transfer performance of two microjet arrays was investigated using degassed deionized water and air. The inline jet arrays had diameters of 54 μm and 112 μm, a spacing of 250 μm, ... -
Analytical Modeling of Annular Flow Boiling Heat Transfer in Mini- and Microchannel Heat Sinks
(The American Society of Mechanical Engineers (ASME), 2010)An analytical model is proposed to predict the flow boiling heat transfer coefficient in the annular flow regime in mini- and microchannel heat sinks based on the separated model. The modeling ... -
Pool Boiling Heat Transfer of Water on Finned Surfaces at Near Vacuum Pressures
(The American Society of Mechanical Engineers (ASME), 2010)This research paper presents a study of boiling heat transfer from longitudinal rectangular-finned surfaces immersed in saturated water at low vapor pressures. Finned surfaces with assorted fin ... -
Thermal Analysis and Optimization of Orthotropic Pin Fins: A Closed-Form Analytical Solution
(The American Society of Mechanical Engineers (ASME), 2010)Analytical solutions for temperature distribution, heat transfer rate, and fin efficiency and fin effectiveness are derived and presented for orthotropic two-dimensional pin fins subject to ... -
Numerical Investigation of Heat Transfer Enhancement in a Microchannel With Grooved Surfaces
(The American Society of Mechanical Engineers (ASME), 2010)This paper presents a numerical investigation for two types of grooves (rectangular and arc shapes) fabricated in the microchannel surfaces, which leads to enhancement in single-phase cooling. ... -
Flow Boiling on Micropin Fins Entrenched Inside a Microchannel—Flow Patterns and Bubble Departure Diameter and Bubble Frequency
(The American Society of Mechanical Engineers (ASME), 2010)Flow boiling of HFE 7000 in five parallel microchannels of 222 μm hydraulic diameter, each containing a single row of 24 in-line 100 μm pin fins, was investigated. High speed photography ...