Journal of Structural Engineering: Recent submissions
Now showing items 5141-5160 of 10765
-
Rotational Spring Analogy for Buckling Analysis
(American Society of Civil Engineers, 2007)This paper presents a “rotational spring” analogy which allows the geometric stiffness for a large class of structural problems to be formulated using common notions from linear structural analysis. The proposed analogy ... -
Probabilistic Performance-Based Optimal Design of Steel Moment-Resisting Frames. I: Formulation
(American Society of Civil Engineers, 2007)Significant progress has been made in the preceding two decades in the area of seismic engineering. Design codes are very quickly migrating from prescriptive procedures intended to preserve life safety to reliability-based ... -
Design Expression for the In-Plane Shear Strength of Reinforced Concrete Masonry
(American Society of Civil Engineers, 2007)Aspects relating to codification of the in-plane shear strength of concrete masonry walls when subjected to seismic loading are presented in this paper. Particular emphasis is placed on a model that is capable of representing ... -
Load-Carrying Capacity of Timber–Concrete Joints with Dowel-Type Fasteners
(American Society of Civil Engineers, 2007)This paper analyzes the load-carrying capacity of timber–concrete joints made with dowel-type fasteners. The scope of the work was to obtain information to be used in the design of timber–concrete composite structures. In ... -
Partition Walls and Their Restraining Effect on Warp in Built-In Wall Studs
(American Society of Civil Engineers, 2007)The focus is on understanding the behavior of walls with regard to the propensity of studs to warp at different moisture content. Experimental tests on whole wall structures were conducted. The walls were built up using ... -
Numerical Bond Analysis Using Experimentally Derived Local Bond Laws: A Powerful Method for Evaluating the Bond Strength of Steel Bars
(American Society of Civil Engineers, 2007)The transfer of forces across the interface between steel bars and concrete through bond is one of the most important aspects that control the behavior of reinforced concrete members. This paper summarizes the results of ... -
Cable Vibration Control with a TMD-MR Damper System: Experimental Exploration
(American Society of Civil Engineers, 2007)Although traditional mechanical dampers can help reduce cable vibrations, they are not the most effective solution due to their position restrictions. Tuned mass dampers (TMDs) were proposed to overcome this limitation and ... -
Large-Displacement Analysis of Planar RC Structures
(American Society of Civil Engineers, 2007)This paper proposes a new planar reinforced concrete (RC) formulation capable of modeling geometric and material nonlinearity. A new co-rotational sub-parametric formulation consisting of a four-noded element with quadratic ... -
Editor’s Note
(American Society of Civil Engineers, 2007) -
Development of Multidirectional Structural Testing System Applicable to Pseudodynamic Test
(American Society of Civil Engineers, 2007)An accurate multidirectional structural testing system is developed. This testing system is used to carry out a multidirectional pseudodynamic test with the help of a unique three-dimensional hinge and a spatial truss-type ... -
Interface Failure Mechanics of Elastically (Advanced Composite) Reinforced Steel Members
(American Society of Civil Engineers, 2007)Tests on steel beams with adhesively bonded elastic reinforcing strips are used to deduce the mechanics of stress build up in the steel-to-strip interface up to failure. The solely elastic nature of the strips is a key ... -
Earthquake Input Energy to Two Buildings Connected by Viscous Dampers
(American Society of Civil Engineers, 2007)A frequency-domain method is developed for evaluating the earthquake input energy to two building structures connected by viscous dampers. It is shown that the earthquake input energies to respective building structures ... -
Web Yielding, Crippling, and Lateral Buckling under Post Loading
(American Society of Civil Engineers, 2007)Unstiffened, unbraced steel beams used in bridge falsework are subjected to patch loads from timber or steel posts. This paper investigates the critical web limit states in these types of beams experimentally and through ... -
Flexural Strength for General Lateral–Torsional Buckling
(American Society of Civil Engineers, 2007)The lateral–torsional buckling behavior of general prismatic and tapered steel members with doubly and singly symmetric sections are investigated based on the general forms of differential equilibrium equations for minor-axis ... -
Coupled Tilt and Translational Ground Motion Response Spectra
(American Society of Civil Engineers, 2007)Dynamic response of structures subjected to earthquake-induced base excitations are often simplified by ignoring the tilt components of ground motion. However, close to the earthquake source, tilting of the ground surface ... -
Collapse Behavior of Steel Special Moment Resisting Frame Connections
(American Society of Civil Engineers, 2007)There is a common perception that seismic detailing can improve the collapse resistance of steel frame buildings. However, the effect on connection performance of the potentially large catenary, i.e., tensile, forces that ... -
Safety Evaluation of Low-Rise Steel Structures under Wind Loads by Nonlinear Database-Assisted Technique
(American Society of Civil Engineers, 2007)The design of a large proportion of the low-rise metal buildings in the United States is based on the ASCE 7-93 Standard and the use of allowable stress design (ASD). In this paper we examine, for a typical case, the ... -
Finite-Element Simulation of Ductile Fracture in Reduced Section Pull-Plates Using Micromechanics-Based Fracture Models
(American Society of Civil Engineers, 2007)Micromechanics-based models that capture interactions of stress and strain provide accurate criteria to predict ductile fracture in finite-element simulations of structural steel components. Two such models—the void growth ... -
Evaluation of 3D Steel Moment Frames under Earthquake Excitations. II: Reliability and Redundancy
(American Society of Civil Engineers, 2007)In NEHRP 2003, a new mechanism-based reliability/redundancy factor, -
Experimental and Analytical Study of Prestressed Steel–Concrete Composite Beams Considering Slip Effect
(American Society of Civil Engineers, 2007)This paper investigates the behavior of simply supported prestressed steel–concrete composite beams through experimental and analytical studies. Eight specimens were instrumented and tested in the experimental program ...