Journal of Structural Engineering: Recent submissions
Now showing items 4881-4900 of 10765
-
Uniaxial Shear-Flexure Model for Reinforced Concrete Elements
(American Society of Civil Engineers, 2008)A simple approach was developed for performance-based analysis of reinforced concrete columns subjected to shear, flexure and axial loads. This method is based on a simplification of a consistent but relatively more complex ... -
Unified Flexural Resistance Equations for Stability Design of Steel I-Section Members: Uniform Bending Tests
(American Society of Civil Engineers, 2008)The 2004 AASHTO and 2005 AISC provisions for flexural design of steel I-section members have been revised in their entirety relative to previous specifications to simplify their logic, organization, and application, while ... -
Unified Flexural Resistance Equations for Stability Design of Steel I-Section Members: Moment Gradient Tests
(American Society of Civil Engineers, 2008)The 2004 AASHTO and 2005 AISC provisions for flexural design of steel I-section members have been revised in their entirety relative to previous specifications to simplify their logic, organization, and application, ... -
Ductility and Energy Dissipation Capacity of Shear-Dominated Steel Plate Walls
(American Society of Civil Engineers, 2008)An experimental study was performed to investigate the potential maximum ductility and energy dissipation capacity of steel plate walls with thin infill plates. Three specimens of a three-story steel plate wall were tested. ... -
Direct Analysis and Design of Steel Frames Accounting for Partially Restrained Column Base Conditions
(American Society of Civil Engineers, 2008)The 2005 AISC specification provides a new method for stability design of steel frame structures termed the direct analysis method (DM). This paper addresses the consideration of partial base fixity using the DM. A refined ... -
Global Lateral Buckling of I-Shaped Girder Systems
(American Society of Civil Engineers, 2008)A closed form solution for elastic global buckling of twin girder systems interconnected with cross frames is derived. Current design specifications for such systems only consider individual girder buckling between cross ... -
Investigation of the Axial Load Capacity for Lightly Reinforced Wall Piers
(American Society of Civil Engineers, 2008)A large number of reinforced concrete buildings constructed prior to the mid-1970s in western North America rely on lightly reinforced, perforated, perimeter shear walls to resist earthquake-induced lateral forces. Although ... -
Three-Stage Full-Range Stress-Strain Model for Stainless Steels
(American Society of Civil Engineers, 2008)Advanced numerical modeling of cold-formed stainless steel members, from manufacturing to full-range response under applied loading, requires knowledge of the stress-strain relationship of the material over a wide range ... -
Low-Rise Steel Structures under Directional Winds: Mean Recurrence Interval of Failure
(American Society of Civil Engineers, 2008)The Commentary to the American Society of Civil Engineers (ASCE) Standard 7-05 states that the nominal mean recurrence interval (MRI) of the wind speed inducing the design strength is about 500 years if the specified load ... -
Seismic Response of Tall Guyed Masts to Asynchronous Multiple-Support and Vertical Ground Motions
(American Society of Civil Engineers, 2008)The seismic behavior of tall masts was investigated with special considerations for the realistic modeling of ground motion at the supports. Three existing masts with varying heights of 213, 313, and -
Unified Flexural Resistance Equations for Stability Design of Steel I-Section Members: Overview
(American Society of Civil Engineers, 2008)The 2004 AASHTO and 2005 AISC provisions for flexural design of steel I-section members have been revised in their entirety relative to previous specifications to simplify their logic, organization, and application, ... -
Experimental and Numerical Analysis of a Glass-to-Steel Joint
(American Society of Civil Engineers, 2008)The aim of the paper is to investigate the tensile strength of a glass pane with holes, such as that commonly used in glass-to-steel joints. Experimental tests have been conducted on a series of glass panes made of ... -
Discussion of “Inelastic Buckling of Reinforcing Bars” by Sungjin Bae, Alexa M. Mieses, and Oguzhan Bayrak
(American Society of Civil Engineers, 2008) -
Discussion of “Inelastic Buckling of Reinforcing Bars” by Sungjin Bae, Alexa M. Mieses, and Oguzhan Bayrak
(American Society of Civil Engineers, 2008) -
Closure to “Inelastic Buckling of Reinforcing Bars” by Sungjin Bae, Alexa M. Mieses, and Oguzhan Bayrak
(American Society of Civil Engineers, 2008) -
Shear Resistance of Transversely Stiffened Steel I-Girders
(American Society of Civil Engineers, 2008)This paper evaluates the accuracy and ease of use of 12 of the most promising models for the shear resistance of transversely stiffened steel I-girders. Several models that are well established in civil engineering practice ... -
Shear Strength and Moment-Shear Interaction in Transversely Stiffened Steel I-Girders
(American Society of Civil Engineers, 2008)With the advent of HPS495W steel, hybrid I-girders have again become advantageous in bridge design. Unfortunately, the use of tension field action is not permitted in determining the shear resistance of hybrid girders in ... -
Editor’s Note
(American Society of Civil Engineers, 2008) -
Steel Fiber-Reinforced Self-Compacting Concrete: Experimental Research and Numerical Simulation
(American Society of Civil Engineers, 2008)Over the last few decades, the astonishing developments of superplasticizers technology allowed great achievements in the conception of concrete mixes exhibiting self-compacting ability. Since the 1980s, some methodologies ... -
Dependence of Damping Correction Factors for Response Spectra on Duration and Numbers of Cycles
(American Society of Civil Engineers, 2008)Many modern applications in earthquake engineering require the use of pseudoacceleration response spectra or relative displacement response spectra calculated for damping ratios other than the commonly assumed 5% of critical. ...