Journal of Structural Engineering: Recent submissions
Now showing items 3181-3200 of 10765
-
Closure to “<i>Structural Serviceability: Floor Vibrations</i>” by Bruce Ellingwood and Andrew Tallin (February, 1984)
(American Society of Civil Engineers, 1985) -
Ultimate Strength of RC Wall Panels with Openings
(American Society of Civil Engineers, 1990)Test results of 12 reinforced concrete (RC) wall panels with openings are presented. The panels have been subjected to in‐plane vertical loads applied at an eccentricity to represent possible accidental eccentricity that ... -
Discussion of “<i>Procedure for Predicting Wind Damage to Buildings</i>” by Kishor C. Mehta, James R. McDonald, and Douglas A. Smith (November, 1981)
(American Society of Civil Engineers, 1983) -
Editor's Note
(American Society of Civil Engineers, 2000) -
Discussion of “Design of Circular Thin-Walled Concrete Filled Steel Tubes,” by Martin D. O’Shea, M.ASCE and Russel Q. Bridge, F.ASCE
(American Society of Civil Engineers, 2002) -
Editor’s Note
(American Society of Civil Engineers, 2008) -
Effect of Active versus Passive Confinement on Seismic Response of Wide RC Columns with Lap Splices
(American Society of Civil Engineers, 2015)The results of an experimental study on seismic bond strengthening of spliced reinforcement in wide RC columns using external confinement are presented. Two types of confinement techniques were evaluated and compared, as ... -
Closure to “<i>Membrane Forces Acting on a Box Girder Bridge</i>” by Kenneth W. Shushkewich (August, 1986, Vol. 112, No. 8)
(American Society of Civil Engineers, 1988) -
Erratum for “Tension Chord Model Modification for Uniaxial Unloading and Reloading in Elastic and Plastic States” by Robert Koppitz, Albin Kenel, and Thomas Keller
(American Society of Civil Engineers, 2014) -
Limit Analysis of Welded Tee End Connections for Hollow Tubes
(American Society of Civil Engineers, 1990)This paper presents a limit analysis, based on the yield line approach, for predicting the ultimate capacity of welded tee end connections for hollow tubes. Five failure mechanisms are identified. The failure mechanisms ... -
Double‐Tapered Glulam Beams: Finite Element Analysis
(American Society of Civil Engineers, 1984)Stresses in double‐tapered, straight‐forward glulam beams are investigated by use of an orthotropic finite element method of analysis. Geometric and elastic materials parameters were varied to establish the sensitivity of ... -
Closure to “Nonlinear Elastic Behavior of I‐Beams Curved in Plan” by Yong‐Lin Pi and N. S. Trahair
(American Society of Civil Engineers, 1998) -
Shake Table Tests on Suspended Nonstructural Components Anchored in Cyclically Cracked Concrete
(American Society of Civil Engineers, 2014)Insufficient anchorage of nonstructural components is a substantial cause of earthquake damage. To investigate this issue, shake table tests were conducted on model nonstructural components suspended and supported via ... -
Discussion of “<i>On Minimum Reinforcement in Concrete Structures</i>” by Franco Levi (December, 1985, Vol. 111, No. 12)
(American Society of Civil Engineers, 1987) -
Discussion of “Equivalent Static Wind Loads on Long-Span Roof Structures” by J. Fu, Z. Xie, and Q. S. Li
(American Society of Civil Engineers, 2010) -
<i>Shells of Revolution</i>
(American Society of Civil Engineers, 1992) -
Finite-Element Analysis of Hollow Flange Beams with Web Stiffeners
(American Society of Civil Engineers, 1997)A new cold-formed and resistance-welded section known as the hollow flange beam (HFB) has been developed recently in Australia. In contrast to the common lateral-torsional buckling mode of I-beams, this unique section ... -
Discussion of “<i>Geometric and Material Nonlinear Analysis of Thin‐Walled Beam‐Columns</i>” by J. L. Meek and W. J. Lin (June, 1990, Vol. 116, No. 6)
(American Society of Civil Engineers, 1992) -
Editor's Note
(American Society of Civil Engineers, 2003) -
Frame Element with Mixed Formulations for Composite and RC Members with Bond Slip. I: Theory and Fixed-End Rotation
(American Society of Civil Engineers, 2015)This paper proposes a composite frame element for the simulation of the inelastic response of structural members made up of two or more components with different materials, such as reinforced concrete (RC), steel-concrete ...