Journal of Structural Engineering: Recent submissions
Now showing items 1741-1760 of 10765
-
Predicting Time-Dependent Behavior of Post-Tensioned Concrete Beams: Discrete Multiscale Multiphysics Formulation
(American Society of Civil Engineers, 2019)Time-dependent deformations, including creep and shrinkage, are essential factors that govern multiple design aspects of prestressed/post-tensioned concrete structures. These include (but are not limited to) time to initial ... -
Experimental Investigation of Cross-Sectional Bending Capacity of Cold-Formed Steel Channels Subject to Local-Distortional Buckling Interaction
(American Society of Civil Engineers, 2019)This paper describes an experimental program carried out at the University of Sheffield to investigate the interaction of local and distortional buckling in cold-formed steel lipped channel beams. The channels were arranged ... -
Proposal to Improve the DSM Design of Cold-Formed Steel Angle Columns: Need, Background, Quality Assessment, and Illustration
(American Society of Civil Engineers, 2019)This paper presents a proposal for the codification of an efficient design approach based on the direct strength method (DSM) for cold-formed steel equal-leg angle columns with short-to-intermediate lengths, i.e., those ... -
Cold-Formed Lean Duplex Stainless Steel Tubular Members under Concentrated Interior Bearing Loads
(American Society of Civil Engineers, 2019)In this study, a total of 58 tests were performed on cold-formed lean duplex stainless steel (LDSS) tubular members under three different loading conditions of concentrated interior bearing forces. The loading conditions ... -
Seismic Design and Performance Evaluation of Long-Span Special Truss Moment Frames
(American Society of Civil Engineers, 2019)The need for a very-long-span structure in sporting and industrial venues puts steel moment frames and braced frames at a disadvantage. In this regard, special truss moment frames (STMFs) can accommodate a large span by ... -
Shake Table Seismic Performance Assessment of Auxiliary Battery Power Systems Using the FEMA 461 Protocol
(American Society of Civil Engineers, 2019)Auxiliary batteries and battery rack systems are widely used as a risk mitigation strategy in several critical facilities to supply power following loss of external power from the grid. Although these systems might fail ... -
Development of Fully Prefabricated Steel-UHPC Composite Deck System
(American Society of Civil Engineers, 2019)This paper proposes a novel fully prefabricated composite deck system to achieve green and accelerated construction in bridge engineering. Ultra-high-performance concrete (UHPC), which has excellent mechanical properties, ... -
Cyclic Response of Sloped Steel Moment Connections
(American Society of Civil Engineers, 2019)For seismic applications in special and intermediate steel moment frames, the design standard provides a number of prequalified connections. This assumes that the beam frames orthogonally into the column in the elevation ... -
Out-of-Plane Performance of Reinforced Masonry Shear Walls Constructed with Boundary Elements
(American Society of Civil Engineers, 2019)Reinforced masonry shear walls with boundary elements have been introduced recently as a seismic force–resisting system as alternative to traditional reinforced masonry shear walls with rectangular cross sections. The ... -
Experimental Performance of Block-Out Connections at the Base of Steel Moment Frames
(American Society of Civil Engineers, 2019)In a block-out connection, a steel column is connected to a footing through an opening (block-out) in a slab-on-grade that is later filled with unreinforced concrete. In design, engineers generally neglect any beneficial ... -
An Unstiffened Eight-Bolt Extended End-Plate Moment Connection for Special and Intermediate Moment Frames
(American Society of Civil Engineers, 2019)Bolted extended end-plate (BEEP) moment-resisting connections are prequalified for use in special and intermediate moment frames. The current limits of this prequalification dictate that rolled wide-flange sections with a ... -
Cyclic Analyses of Reinforced Concrete Masonry Panels Using a Force-Based Frame Element
(American Society of Civil Engineers, 2019)This paper presents the calibration of a frame element that can be used to model the flexural as well as the shear behavior of reinforced masonry panels subjected to monotonic and cyclic loads. The element can be used in ... -
Experimental and Analytical Investigations of a Timber–Concrete Composite Beam Using a Hardwood Interface Layer
(American Society of Civil Engineers, 2019)This paper presents a study that examined the use of a new connection system in a prefabricated timber–concrete composite (TCC) beam in which a hardwood layer was glued to the top of a timber web to reinforce a dowel-type ... -
Reliability Analysis of Steel SMRF and SCBF Structures Considering the Vertical Component of Near-Fault Ground Motions
(American Society of Civil Engineers, 2019)This paper assesses the effects of the vertical component of ground motions on steel structures and evaluates the current seismic design provisions of ASCE 7 on the basis of a structural reliability outlook. Eight special ... -
Blast-Wave Clearing for Detonations of High Explosives
(American Society of Civil Engineers, 2019)When a blast wave impinges on the front face of a structure, rarefaction waves are formed along its free edges and propagate toward the center of the front face, and reduce the reflected overpressure: an effect known as ... -
Preliminary Design of Moment-Resisting Frame Buildings for Tolerable Financial Loss
(American Society of Civil Engineers, 2019)This paper aims to transfer the current performance-based seismic assessment (PBSA) methodology to engineering practice by providing a preliminary design procedure denoted herein as the preliminary performance-based seismic ... -
Elastic-Plastic Analysis of Bolted Angles Usable in Steel Frame Connections
(American Society of Civil Engineers, 2019)An analytical model was proposed to predict the monotonic load-deformation behavior of bolted angles used in semirigid steel frame connections. This model was validated using the results of 30 pull tests performed on bolted ... -
Vision-Based Modal Survey of Civil Infrastructure Using Unmanned Aerial Vehicles
(American Society of Civil Engineers, 2019)Computer vision techniques for extracting dynamic structural displacements from videos are gaining increasing acceptance for the purposes of system identification and structural health monitoring. However, the application ... -
Analytical Pushover Method and Hysteretic Modeling of Precast Segmental Bridge Piers with High-Strength Bars Based on Cyclic Loading Test
(American Society of Civil Engineers, 2019)Compared to cast-in-place bridge piers, precast piers can accelerate bridge construction, but their use in seismic systems is challenging. High-strength bars (≥500 MPa) incorporated with precast piers can further expedite ... -
Steel-Plate Composite Wall-to-Wall T-Joints: Joint Shear Strength
(American Society of Civil Engineers, 2019)Steel-plate composite (SC) walls are used in the containment internal structures (CIS) of safety-related nuclear facilities. CIS are typically composed of multiple SC walls intersecting each other and forming SC wall-to-wall ...