• Login
    View Item 
    •   DSpace Home
    • ASME
    • Journal of Pressure Vessel Technology
    • View Item
    •   DSpace Home
    • ASME
    • Journal of Pressure Vessel Technology
    • View Item
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Limit Load Determination and Material Characterization of Cracked Polyethylene Miter Pipe Bends1

    Thumbnail
    View/Open
    pvt_136_04_041203.pdf (3.733Mb)
    Date
    2014
    Author
    EL
    Younan, Maher Y. A.
    Sallam, Hossam E. M.
    Abdel
    Metadata
    Show full item record
    Abstract
    The quality of Natural Gas Piping Systems (NGPS), must be ensured against manufacturing defects. The main purpose of the present paper is to investigate the effect of loading mode and load angle (30 deg, 45 deg, and 60 deg) on the limit load of miter pipe bends (MPB), under different crack depths a/W = 0–0.4 at a crosshead speed 500 mm/min. The geometry of cracked and uncracked multimiter pipe bends are pipe bend angle, خ±â€‰= 90 deg, pipe bend factor, h = 0.844, standard dimension ratio, SDR = 11, and three junctions, m = 3. The material of the investigated pipe is a highdensity polyethylene (HDPE), which is commonly used in NGPS. The welds at the miter pipe junction are produced by buttfusion welding. For all loading modes the limit load is obtained by the tangent intersection (TI) method from the load–deflection curves produced by the specially designed and constructed testing machine at the laboratory5. Tensile tests are conducted on specimens longitudinally extruded from the pipe with thickness, T = 10, 30 mm, at different crosshead speeds (5–500 mm/min), and different gauge lengths (G = 20, 25, and 50 mm) to determine the mechanical properties of welded and unwelded specimens. The fracture toughness is determined on the basis of elastic plastic fracture mechanics (EPFM). Curved threepoint bend specimens (CTPB), are used. All specimens are provided with artificial precrack at the crack tip, a/W = 0.5. The effect of specimen thickness variation (B = 10, 15, 22.5, 30, 37.5, and 45 mm) for welded and unwelded specimens is studied at room temperature (Ta = 23 آ°C) and at different crosshead speeds, VC.H, ranging from 5 to 500 mm/min. The study reveals that increasing the crack depth leads to a decrease in the stiffness and limit load of MPB for both inplane, and outofplane bending moment. In case of combined load (outofplane and inplane opening; mode), higher load angles lead to an increase in the limit load. The highest limit load value occurs at a loading angle, د• = 60 deg. In case of combined load (outofplane and inplane closing; mode), the limit load decreases with increasing load angles. At a load angle د• = 30 deg, the higher limit load value occurred in both cases. For combined load opening case, higher values of limit load are obtained. The crosshead speed has a significant effect on the mechanical behavior of both welded and unwelded specimens. The fracture toughness, JIC, is greater for unwelded than welded specimen.
    URI
    http://yetl.yabesh.ir/yetl/handle/yetl/156154
    Collections
    • Journal of Pressure Vessel Technology

    DSpace software copyright © 2002-2015  DuraSpace
    Contact Us | Send Feedback
    Theme by 
    @mire NV
     

     

    Browse

    All of DSpaceCommunities & CollectionsBy Issue DateAuthorsTitlesSubjectsThis CollectionBy Issue DateAuthorsTitlesSubjects

    My Account

    LoginRegister

    Statistics

    View Usage Statistics

    DSpace software copyright © 2002-2015  DuraSpace
    Contact Us | Send Feedback
    Theme by 
    @mire NV