Show simple item record

dc.contributor.authorSébastien Luciani
dc.contributor.authorDavid Brutin
dc.contributor.authorChristophe Le Niliot
dc.contributor.authorOuamar Rahli
dc.contributor.authorLounès Tadrist
dc.date.accessioned2017-05-09T00:28:53Z
dc.date.available2017-05-09T00:28:53Z
dc.date.copyrightOctober, 2008
dc.date.issued2008
dc.identifier.issn0022-1481
dc.identifier.otherJHTRAO-27845#101502_1.pdf
dc.identifier.urihttp://yetl.yabesh.ir/yetl/handle/yetl/138444
dc.description.abstractBoiling in microchannels is a very efficient mode of heat transfer since high heat and mass transfer coefficients are achieved. Here, the objective is to provide basic knowledge on the systems of biphasic cooling in mini- and microchannels during hyper- and microgravity. The experimental activities are performed in the frame of the MAP Boiling project founded by ESA. Analysis using inverse methods allows us to estimate local flow boiling heat transfers in the minichannels. To observe the influence of gravity level on the fluid flow and to take data measurements, an experimental setup is designed with two identical channels: one for the visualization and the other one for the data acquisition. These two devices enable us to study the influence of gravity on the temperature and pressure measurements. The two minichannels are modeled as a rectangular rod made up of three materials: a layer of polycarbonate (λ=0.2Wm−1K−1) used as an insulator, a cement rod (λ=0.83Wm−1K−1) instrumented with 21 K-type thermocouples, and in the middle a layer of Inconel® (λ=10.8Wm−1K−1) in which the minichannel is engraved. Pressure and temperature measurements are carried out simultaneously at various levels of the minichannel. Above the channel, we have a set of temperature and pressure gauges and inside the cement rods, five heating wires provide a power of 11W. The K-type thermocouple sensors enable us to acquire the temperature in various locations (x, y, and z) of the device. With these temperatures and the knowledge of the boundary conditions, we are able to solve the problem using inverse methods and obtain local heat fluxes and local surface temperatures on several locations. The experiments are conducted with HFE-7100 as this fluid has a low boiling temperature at the cabin pressure on Board A300. We applied for each experiment a constant heat flux (Qw=33kWm−2) for the PF52 campaigns (Parabolic Flights). The mass flow rate varies in the range of 1<Qm<4gs−1 and the fluid saturation temperature (Tsat) is 54°C at Psat=820mbars.
dc.publisherThe American Society of Mechanical Engineers (ASME)
dc.titleFlow Boiling in Minichannels Under Normal, Hyper-, and Microgravity: Local Heat Transfer Analysis Using Inverse Methods
dc.typeJournal Paper
dc.journal.volume130
dc.journal.issue10
dc.journal.titleJournal of Heat Transfer
dc.identifier.doi10.1115/1.2953306
dc.journal.fristpage101502
dc.identifier.eissn1528-8943
dc.keywordsTemperature
dc.keywordsHeat transfer
dc.keywordsMeasurement
dc.keywordsGravity (Force)
dc.keywordsFlow (Dynamics)
dc.keywordsCements (Adhesives)
dc.keywordsBoiling
dc.keywordsBoundary-value problems
dc.keywordsThermocouples
dc.keywordsHeat flux
dc.keywordsHeat
dc.keywordsErrors
dc.keywordsSensors
dc.keywordsInverse problems
dc.keywordsHeating
dc.keywordsBoundary element methods
dc.keywordsHeat transfer coefficients
dc.keywordsFlight
dc.keywordsEquations
dc.keywordsNoise (Sound)
dc.keywordsWire AND Dimensions
dc.treeJournal of Heat Transfer:;2008:;volume( 130 ):;issue: 010
dc.contenttypeFulltext


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record