Show simple item record

dc.contributor.authorK. P. Jen
dc.contributor.authorJ. N. Majerus
dc.date.accessioned2017-05-08T23:35:38Z
dc.date.available2017-05-08T23:35:38Z
dc.date.copyrightOctober, 1991
dc.date.issued1991
dc.identifier.issn0094-4289
dc.identifier.otherJEMTA8-26945#475_1.pdf
dc.identifier.urihttp://yetl.yabesh.ir/yetl/handle/yetl/108602
dc.description.abstractThis paper presents the evaluation of the stress-strain behavior, as a function of strain-rate, for three tin-lead solders at room temperature. This behavior is critically needed for reliability analysis of printed circuit boards (PCB) since handbooks list minimal mechanical properties for the eutectic solder used in PCBs. Furthermore, most handbook data are for stable eutectic microstructure whereas PCB solder has a metastable microstructure. All three materials were purchased as “eutectics.” However, chemical analysis, volume fraction determination, and microhardness tests show some major variations between the three materials. Two of the materials have a eutectic composition, and one does not. The true stress-strain equations of one eutectic and the one noneutectic material are determined from compressive tests at engineering strain-rates between 0.0002/s and 0.2/s. The second eutectic material is evaluated using tensile tests with strain-rates between 0.00017/s and 0.042/s. The materials appear to exhibit linear elastic behavior only at extremely small strains, i.e., less than 0.0005. However, this “elastic” behavior showed considerable variation, and depended upon the strain rate. In both tension and compression the eutectic alloy exhibits nonlinear plastic behavior, i.e., strain-softening followed by strain-hardening, which depends upon the strain rate. A quadratic equation σy = σy (ε̊/ε̊0 ) + A(ε̊/ε̊0 )ε + B(ε̊/ε̊0 )ε2 fit to the data gives correlation coefficients R2 > 0.91. The coefficients σy (ε̊/ε̊0 ), A(ε̊/ε̊0 ), B(ε̊/ε̊0 ) are fitted functions of the normalized engineering strain rate ε̊/ε̊0 . Replicated experiments are used at each strain-rate so that a measure of the statistical variation could be estimated. Measures of error associated with the regression analysis are also obtained so that an estimate of the total error in the stress-strain relations can be made.
dc.publisherThe American Society of Mechanical Engineers (ASME)
dc.titleStress-Strain Equations for Some Near-Eutectic Tin-Lead Solders
dc.typeJournal Paper
dc.journal.volume113
dc.journal.issue4
dc.journal.titleJournal of Engineering Materials and Technology
dc.identifier.doi10.1115/1.2904128
dc.journal.fristpage475
dc.journal.lastpage484
dc.identifier.eissn1528-8889
dc.keywordsEquations
dc.keywordsSolders
dc.keywordsStress
dc.keywordsErrors
dc.keywordsEutectic alloys
dc.keywordsFunctions
dc.keywordsMicrohardness
dc.keywordsRegression analysis
dc.keywordsTension
dc.keywordsWork hardening
dc.keywordsPrinted circuit boards
dc.keywordsEvent history analysis
dc.keywordsMechanical properties
dc.keywordsStress-strain relations
dc.keywordsCompression
dc.keywordsElasticity AND Temperature
dc.treeJournal of Engineering Materials and Technology:;1991:;volume( 113 ):;issue: 004
dc.contenttypeFulltext


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record