Show simple item record

dc.contributor.authorD. I. Roberts
dc.contributor.authorR. Viswanathan
dc.contributor.authorR. H. Ryder
dc.date.accessioned2017-05-08T23:20:59Z
dc.date.available2017-05-08T23:20:59Z
dc.date.copyrightAugust, 1985
dc.date.issued1985
dc.identifier.issn0094-9930
dc.identifier.otherJPVTAS-28258#247_1.pdf
dc.identifier.urihttp://yetl.yabesh.ir/yetl/handle/yetl/100272
dc.description.abstractDissimilar metal welds (DMWs) between austenitic and ferritic steel tubing and piping are commonly employed in high-temperature applications in energy conversion systems. Differences in coefficient of thermal expansion between the two types of steel induce thermal stresses at the welds and local metallurgical changes near the low alloy steel/weld metal interface due to prolonged service at an elevated temperature. These phenomena, together with the differences in creep behavior of the materials joined, render the DMWs more prone to failure than welds between similar steels. This has been reflected in relatively high failure rates in DMWs in certain service applications (e.g., in utility power plant boiler tubing). Typically these welds fail by low ductility cracking in the low alloy steel at, or very close to, the fusion line. A project, sponsored by the Electric Power Research Institute (EPRI) and managed by the Metal Properties Council (MPC), has made significant headway over the last three years in understanding the failure modes and causes involved and in developing methods to assess residual life of DMWs. Welds from service in superheaters and reheater tubes and from laboratory simulation tests were examined to establish metallurgical characteristics and failure modes. Three failure modes were identified: (i) Prior austenite grain boundary cracking in the ferritic steel, one or two grains away from the fusion line; this mode was mainly observed in DMWs made with stainless steel filler metal. (ii) Cracking along the weld interface, which occurred in DMWs made with nickel-base filler metal. (iii) Propagation of cracks initiating from oxide notches formed at the weld outside surface; this mode occurred mainly in thin-walled tubes. Creep damage induced by steady and cyclic loading was found to be the predominant mechanism for damage and failure; therefore a dependence of damage on loading levels and service temperature was established. It was also determined that failure susceptibility in DMWs made with nickel-base filler was strongly influenced by the type of microstructure that formed at the low alloy steel/weld metal interface. The technique developed for estimating the condition and remaining life of DMWs in service involves detailed assessment of loading histories to which the welds are subjected, along with the use of empirical quantitative relationships established from both laboratory and service data. The methodology assumes that damage results from the combined effects of self damage (caused by thermal cycling of materials of different expansion coefficients) and service loadings, including both primary loads (e.g., pressure and deadweight) and secondary, or cyclic, loads due to the constrained thermal expansion of the system as a whole. The technique, Prediction Of Damage In Service (designated PODIS), has been found to adequately predict levels of damage in stainless-based DMWs in service. It is currently being developed further to embrace nickel-based DMWs.
dc.publisherThe American Society of Mechanical Engineers (ASME)
dc.titlePerformance of Dissimilar Welds in Service
dc.typeJournal Paper
dc.journal.volume107
dc.journal.issue3
dc.journal.titleJournal of Pressure Vessel Technology
dc.identifier.doi10.1115/1.3264443
dc.journal.fristpage247
dc.journal.lastpage254
dc.identifier.eissn1528-8978
dc.keywordsWelded joints
dc.keywordsFailure
dc.keywordsMetals
dc.keywordsSteel
dc.keywordsNickel
dc.keywordsAlloy steel
dc.keywordsFracture (Process)
dc.keywordsFiller metals
dc.keywordsStress
dc.keywordsThermal expansion
dc.keywordsCreep
dc.keywordsTemperature
dc.keywordsElectricity (Physics)
dc.keywordsFillers (Materials)
dc.keywordsGrain boundaries
dc.keywordsSimulation
dc.keywordsTubing
dc.keywordsSuperheaters
dc.keywordsThermal stresses
dc.keywordsDuctility
dc.keywordsEnergy conversion
dc.keywordsStainless steel
dc.keywordsBoiler tubes
dc.keywordsHigh temperature
dc.keywordsMechanisms
dc.keywordsPipes
dc.keywordsPower stations
dc.keywordsCrack propagation AND Pressure
dc.treeJournal of Pressure Vessel Technology:;1985:;volume( 107 ):;issue: 003
dc.contenttypeFulltext


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record