Search
CSV
RISDiscussion: “Specific Heat of Tribological Wear Debris Material†(Maciؤ…g, M., 2015, ASME J. Tribol., 137(3), p. 031601)
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: The thermal load acting on the MAZ is the share of the particular solid from the work of the friction force. The dissipated heat to the bulk of either rubbing solids has two contributions. The first is the heat conducted ...
Three Dimensional Fully Parameterized Triangular Plate Element Based on the Absolute Nodal Coordinate Formulation
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: In this work, a new threedimensional fully parameterized triangular plate element based on the absolute nodal coordinate formulation (ANCF) is introduced. This plate element has 12 coordinates per node; therefore, it can ...
Analysis of Heavily Loaded Tilted Pads Thrust Bearings With Large Dimensions Under TEHD Conditions
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: Huge thrust bearings with centrally pivoted and tilted pads operating under heavy loads are analzyed using the (thermoelastohydrodynamic) TEHD-theory. The Reynolds equation, the energy equation of ...
Quality Improvement in Egypt: Methodology and Implementation
Publisher: American Society of Civil Engineers
Abstract: This paper describes a method of obtaining construction managers' consensus opinion on factors to improve quality on their projects. It also explains the details and results of the application that was carried out in one ...
Education Committee Best Paper of 1996 Award: Response of a Turbofan Engine Compression System to Disturbed Inlet Conditions
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: A generic code DYNTECC has been adapted to perform a parametric study of the effect of inlet flow distortion on the stability of the Pratt and Whitney TF30 engine. This code was developed ...
Comments on “Thermophysical-property-based selection of tool protective coatings for dry machining of steels” by Wit Grezesik et al., Journal of Manufacturing Science and Engineering., Nov. 2003, Vol. 125, pp. 689–695
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: Thermal matching of coating-tool materials to optimize dry machining of steels is an interesting idea. Grezesik et al. find that the thermal properties of the materials involved, namely, the ...
Efficient Solar Desalination System Using Humidification/Dehumidification Process
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: An innovative solar desalination system is successfully designed, manufactured, and experimentally tested at Makkah, 21.4 degN. The system consists of 1.15 m2 flatplate collector as a heat source and a desalination unit. ...
Discussion: “A Deterministic-Chaos Study of Electron Triboemission Outputs” (Molina, G. J., Furey, M. J., and Kajdas C., 2007, ASME J. Tribol., 129(3), pp. 679–683)
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: The authors observed that the strength of triboemission, for diamond-Si and diamond-Ge pairs, decreased as contact progressed over the same wear track. Nakayama and Fujimoto (1) observed similar ...
Retracted: Effect of Reactive Magnesium Oxide on Properties of Alkali-Activated Slag-Cement Pastes
Publisher: American Society of Civil Engineers
Abstract: The effect of different proportions and different reactivities of MgO on the drying shrinkage and compressive strength of alkali-activated slag pastes (AAS) has been investigated. The slag was activated by 6% by weight ...
Discussion: “An Application of Dimensional Analysis to Entropy-Wear Relationship,” (Amiri, M., Khonsari, M. M., Brahmeshwarkar, S., 2012, J. Tribol., 134 , P. 011604)
Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: The authors present an interesting thermodynamic interpretation of the Archard wear coefficient. However, their interpretation is confined to the steady state. The purpose of this discussion is, ...