Journal of Engineering Materials and Technology: Recent submissions
Now showing items 441-460 of 3257
-
Effect of Surface Contamination on the Diffusion Bonding of Copper
(The American Society of Mechanical Engineers (ASME), 1973)An investigation was made of the effect of cleaning the contacting surfaces of copper samples upon the strength of the diffusion bond formed. The cleaning of surfaces by filing and the diffusion ... -
Finite Element Analysis of the Diametral Test of Polymer Moldings
(The American Society of Mechanical Engineers (ASME), 1973)A finite element analysis of the diametral test is presented and the results are compared with an elastic analysis and with diametral tests of molded pyrrone disks. Both the elastic and the ... -
The Plastic Bending of Beams and Their Failure by Low Cycle Fatigue
(The American Society of Mechanical Engineers (ASME), 1973)The major difficulty in applying high strain fatigue data to technological problems lies not in the fatigue aspect per se but in the prediction of the cyclic strain amplitudes. In this paper ... -
Stress Distribution in a Bonded Anisotropic Lap Joint
(The American Society of Mechanical Engineers (ASME), 1973)A theoretical analysis of a bonded single lap joint is presented. The adherends are considered anisotropic whereas the cement is treated as an isotropic material. The analysis is confined to ... -
The Effect of Temperature Upon the Fatigue-Crack Growth Behavior of Two Nickel-Base Alloys
(The American Society of Mechanical Engineers (ASME), 1973) -
Environment-Assisted Fracture in Engineering Alloys: Part II—Cyclic Loading and Future Work
(The American Society of Mechanical Engineers (ASME), 1973) -
Residual Stresses Due to Circumferential Welds
(The American Society of Mechanical Engineers (ASME), 1973)The residual stress distribution produced by a circumferential weld between axisymmetric shells (cylinders, spheres, cones, etc.) is quite different from that due to a butt weld between two flat ... -
A Note on the Plastic Torsion of a Thin Walled Anisotropic Tube
(The American Society of Mechanical Engineers (ASME), 1973) -
State of Stress During Solidification With Varying Freezing Pressure and Temperature
(The American Society of Mechanical Engineers (ASME), 1973)An analysis is presented to estimate the state of stress when solidification occurs with varying liquid pressure and freezing temperature. A model assuming the state of stress in the freezing ... -
The Indentation and Scratch Hardness of Plastics
(The American Society of Mechanical Engineers (ASME), 1973)Static and sliding indentation tests on vinyl chloride-acetate copolymer and nylon 66 are described, and form part of a study of the deformation and wear of gramophone records. The vinyl was ... -
Environment-Assisted Fracture in Engineering Alloys: Part I—Monotonic Loading
(The American Society of Mechanical Engineers (ASME), 1973) -
On the Compression of a Conical Disk
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “The Super Flywheel: A Second Look” (Brunelle, E. J., 1973, ASME J. Eng. Mater. Technol., 95, pp. 63–65)
(The American Society of Mechanical Engineers (ASME), 1973) -
A Further Study of Residual Stresses in Circumferential Welds
(The American Society of Mechanical Engineers (ASME), 1973)The residual stress distribution for a circumferential weld between cylinders was obtained in a prior publication for a full penetration, single pass weld with no variation of alloy content ... -
Fatigue and Corrosion-Fatigue Crack Propagation in Intermediate-Strength Aluminum Alloys
(The American Society of Mechanical Engineers (ASME), 1973)Fatigue crack propagation studies were conducted on a variety of intermediate-strength aluminum alloys under high stress-intensity range cycling (ΔK > 10 ksiin.). Tests were conducted in ambient ... -
Fractographic Study of Fatigue Crack Propagation
(The American Society of Mechanical Engineers (ASME), 1973)Fractographic studies were carried out on fatigue fracture of aluminum alloys and carbon steels. Special attention was given to the correlation between striation spacing and macroscopic crack ... -
A Fracture Criterion for Cold Forming
(The American Society of Mechanical Engineers (ASME), 1973)Fracture under combined stresses has been studied with the objective of evaluating existing fracture criteria and providing data for the formulation of new criteria. Upsetting, bending, rolling, ... -
Discussion: “Elastic-Plastic Deformation in Edge-Notched Tension Specimens Under Plane Stress Conditions” (Griffis, C. A., 1973, ASME J. Eng. Mater. Technol., 95, pp. 130–132)
(The American Society of Mechanical Engineers (ASME), 1973) -
Tube-Bulging Under Internal Pressure and Axial Force
(The American Society of Mechanical Engineers (ASME), 1973)A numerical solution for analysis of the bulging process of a thin-walled tube under internal pressure and axial force is proposed. The solution is applied to a case in which the longitudinal ... -
Computerized Materials Selection
(The American Society of Mechanical Engineers (ASME), 1973)Two analytical approaches are described for computer-aided selection of engineering materials. With given design or selection properties in mind, various materials within a given class may be ...